1. Minimum Clearances to Combustibles

WITHIN ENCLOSURE AREA:

 

 

 

Appliance to backwall

1 in. (25 mm)

 

Appliance to sidewall

1 in. (25 mm)

 

Duct boots to framing

0 in. (0 mm)

 

Top standoffs to header

0 in. (0 mm)

 

Door opening to sidewall

22-7/8 in. (581 mm)

EXPOSED SURFACES

 

 

 

Faceplate to sidewall

16 in. (406 mm)

 

Heat zone air grills to ceiling

12 in. (305 mm)

 

MANTEL

Combustible and non-combustible mantel minimum height from base of fireplace to underside of mantel

60 in. (1524 mm)

Maximum mantel depth

12 in. (305 mm)

Optional Framing Construction / Reduced Mantel Height:

Non-combustible mantel material minimum height from base of fireplace to underside of mantel 46 in. (1168mm) when the following enclosure construction materials are used:

Non-combustible framing materials must be used above fire- place to height of 84 in. (2134mm) from base of fireplace for all construction materials, framing members, sheeting, and all finish materials.

Non-Combustible Materials

Materials which will not ignite and burn. Such materials are those consisting entirely of steel, iron, brick, tile, concrete, slate, glass or plasters, or any combination thereof.

Materials that are reported as passing ASTM E 136, Stan- dard Test Method for Behavior of Materials, in a Vertical Tube Furnace at 750°C, shall be considered non-combus-

WARNING

Fire Risk

•Non-combustible mantels installed at a reduced height may GET EXTREMELY HOT during use of the fireplace.

•DO NOT TOUCH or place heat sensitive combustible items on the mantel.

CHIMNEY SECTIONS

Chimney sections at any level require a 2 in. (51 mm) mini- mum air space clearance between the framing and chimney section.

C. Frame the Fireplace

NOTE: Wiring for fans must be done before framed enclosure is completed. If using a Heat Zone kit, it also must be installed before enclosure is complete.

The NorthStar Fireplace will fit a framed opening height of 43-7/8 in. (1114 mm) tall and width of 42 in. (1067 mm). The finished cavity depth must be no less than 24 in. (610 mm). Framing must extend straight up all the way to the ceiling.

Figure 12.1 shows a typical framing (using 2 x 4 lumber) of the fireplace, assuming combustible materials are used. All required clearances to combustibles around the fireplace must be adhered to. See Figure 11.1, on page 11. Any fram- ing across the top of the fireplace must be above the level of the top standoffs. (No recess above standoffs.)

2 in.

(51mm)

tible materials.

Combustible Materials

Materials made of or surfaced with wood, compressed paper, plant fibers, plastics, or other materials that can ignite and burn, whether flame proofed or not, or whether plastered or un-plastered shall be considered combustible materials.

WARNING

Fire Risk

Hearth & Home Technologies is not respon- sible for discoloration, cracking or other mate-

43-7/8 in.

(1114mm)

24 in.

(610mm)

12 in.

(305mm)

Position combustible / non-combustible mantel 60 in. (1524mm) from base of the fireplace

42 in.

(1067mm)

rial failures of finishing materials due to heat exposure or smoke.

•Choose finishing materials carefully.

Figure 12.1 Framing the Fireplace

Page 12

Heat & Glo • NorthStar EPA Fireplace • 480-1081C

September 1, 2008

Page 11 Page 13
Page 12
Image 12
Hearth and Home Technologies NorthStar-GT Frame the Fireplace, Minimum Clearances to Combustibles, Combustible Materials
Page 11 Page 13

NorthStar-GT, NorthStar-BK, NorthStar-NT specifications

Hearth and Home Technologies has established itself as a leader in the production of innovative heating appliances, particularly with the launch of its NorthStar series: NorthStar-NT, NorthStar-BK, and NorthStar-GT. These models are designed to deliver superior performance, aesthetic appeal, and advanced technology, making them an excellent choice for modern homes.

The NorthStar-NT model is ideally suited for those seeking a reliable and efficient heating solution. It boasts a powerful, advanced heating technology that maximizes heat output while minimizing fuel consumption. The NorthStar-NT employs a unique combustion system that ensures a cleaner burn, resulting in fewer emissions and a lower environmental impact. The sleek design of the NorthStar-NT allows it to blend seamlessly into any room, making it not just a heating unit but also an attractive focal point.

On the other hand, the NorthStar-BK variant stands out for its versatility and aesthetic flexibility. It offers an array of customizable options, enabling homeowners to match the unit's appearance with their interior decor. The NorthStar-BK features a large viewing area, which enhances the visual appeal of the flames while providing efficient heat distribution. This model incorporates user-friendly controls that allow for easy temperature adjustments, ensuring that comfort is just a button away.

The NorthStar-GT model elevates the heating experience with its advanced smart technology features. Equipped with Wi-Fi connectivity, the NorthStar-GT allows users to control the appliance remotely via a smartphone app. This model also supports voice-activated commands, integrating seamlessly with smart home systems. The NorthStar-GT emphasizes energy efficiency, with programmable settings that enable users to optimize heating schedules to their lifestyle, ultimately contributing to energy savings.

All three NorthStar models feature durable construction and high-quality materials designed to withstand years of use. Their construction ensures not only longevity but also safety, with multiple safety features integrated into each model. Easy maintenance and cleaning options further enhance their user-friendly design.

In summary, the Hearth and Home Technologies NorthStar series including the NorthStar-NT, NorthStar-BK, and NorthStar-GT brings together cutting-edge technology, unparalleled efficiency, and stunning aesthetics. Each model caters to different needs, ensuring that homeowners can find the perfect heating solution that fits their style and requirements.
Top Page Image Contents