4 Installation of Fireplace

 

 

1.

Cut a 6 in. (152 mm) hole in outside wall to accommodate

CAUTION

 

 

 

air piping. The outside air is located on top, auxiliary

 

 

 

convection air intake is located on the bottom. See Figure

 

 

 

Sharp Edges

 

 

15.1.

• Wear protective gloves

 

2.

Use 6 in. (152 mm) metal flex or rigid piping (not supplied)

and safety glasses during

 

 

to directly connect outside air to fireplace intake. Insulate

installation.

 

 

 

 

the pipe to prevent frost condensation.

 

 

 

 

 

 

A. Install the Outside Air Kit

3.

Use the supplied termination caps.

4.

Seal between the wall and the pipe with silicone to prevent

This fireplace will operate correctly only if adequate ventila-

 

moisture penetration and air leaks.

tion is provided to allow proper draft to the fireplace system.

5.

Seal between the termination cap and the house with

See Section 2.

 

silicone to prevent air infiltration.

 

 

 

Using an outside air kit must be used for combustion to mini-

mize the effects of negative pressure within the structure. NOTE: A control knob allows you control of the outside air

We recommend you utilize the shortest duct run to optimize

inlet. Use of outside air for combustion is required to

the performance of the outside air kit. The outside air kit inlet

conserve heated air within the structure and to provide

should be positioned in a manner that will not allow snow,

make up air to keep the fireplace venting properly.

leaves, etc. to block the inlet. In some installations the air

IMPORTANT!

duct may need to be run vertically. In such an installation, a

TURN CLOCKWISE TO “OPEN” POSITION.

3 ft (914 mm) height difference must be maintained from the

top of the uppermost chimney section to the outside com-

OUTSIDE AIR KNOB MUST BE IN THE “OPEN” POSI-

bustion air inlet. See Figure 16.1 on page 16.

TION TO OPERATE FIREPLACE PROPERLY.

See Figure 17.1 on page 17 for proper placement of outside

MAY BE CLOSED WHEN NOT IN USE TO PREVENT

air inlet.

The outside air kit is installed on the right hand side of the

COLD AIR INFILTRATION.

 

fireplace. See Figure 15.1 for handle location/operation.

 

Open/Close

 

 

Termination Cap

 

Knob for

 

 

 

supplied with

 

outside air

OPEN

CLOSE

6 in. (152mm) rigid

fireplace

 

 

 

 

 

or flex pipe

 

 

 

 

 

 

 

Figure 15.1

Outside Air Installation

 

 

 

September 1, 2008

Heat & Glo • NorthStar EPA Fireplace • 480-1081C

 

Page 15

Page 14 Page 16
Page 15
Image 15
Hearth and Home Technologies NorthStar-GT, NorthStar-NT owner manual Installation of Fireplace, Install the Outside Air Kit
Page 14 Page 16

NorthStar-GT, NorthStar-BK, NorthStar-NT specifications

Hearth and Home Technologies has established itself as a leader in the production of innovative heating appliances, particularly with the launch of its NorthStar series: NorthStar-NT, NorthStar-BK, and NorthStar-GT. These models are designed to deliver superior performance, aesthetic appeal, and advanced technology, making them an excellent choice for modern homes.

The NorthStar-NT model is ideally suited for those seeking a reliable and efficient heating solution. It boasts a powerful, advanced heating technology that maximizes heat output while minimizing fuel consumption. The NorthStar-NT employs a unique combustion system that ensures a cleaner burn, resulting in fewer emissions and a lower environmental impact. The sleek design of the NorthStar-NT allows it to blend seamlessly into any room, making it not just a heating unit but also an attractive focal point.

On the other hand, the NorthStar-BK variant stands out for its versatility and aesthetic flexibility. It offers an array of customizable options, enabling homeowners to match the unit's appearance with their interior decor. The NorthStar-BK features a large viewing area, which enhances the visual appeal of the flames while providing efficient heat distribution. This model incorporates user-friendly controls that allow for easy temperature adjustments, ensuring that comfort is just a button away.

The NorthStar-GT model elevates the heating experience with its advanced smart technology features. Equipped with Wi-Fi connectivity, the NorthStar-GT allows users to control the appliance remotely via a smartphone app. This model also supports voice-activated commands, integrating seamlessly with smart home systems. The NorthStar-GT emphasizes energy efficiency, with programmable settings that enable users to optimize heating schedules to their lifestyle, ultimately contributing to energy savings.

All three NorthStar models feature durable construction and high-quality materials designed to withstand years of use. Their construction ensures not only longevity but also safety, with multiple safety features integrated into each model. Easy maintenance and cleaning options further enhance their user-friendly design.

In summary, the Hearth and Home Technologies NorthStar series including the NorthStar-NT, NorthStar-BK, and NorthStar-GT brings together cutting-edge technology, unparalleled efficiency, and stunning aesthetics. Each model caters to different needs, ensuring that homeowners can find the perfect heating solution that fits their style and requirements.
Top Page Image Contents