Models | Heat & Glo LifeStyle 6000C specs

Finishing Material Thickness: 1-4 inches maximum

NOTICE: Remove finishing strips before firing appliance.

FINISHING

STRIPS USED

NON-COMBUSTIBLE

FINISHING MATERIAL

FINISHING	FINISHING
MATERIAL	MATERIAL

DOOR

A

(Outside door width)

C

(Includes 1/8 in. opening each side of door)

B

A

D

(Outside door width)

C

(Includes 1/8 in. opening each side of door)

Finishing material thickness, 1-4 inches maximum B = Top of door to bottom of fireplace.

D = Bottom of Finishing Material to Bottom of Fireplace

Figure 13.5 Finishing Material Thickness Greater Than One Inch

Finishing Material Thickness: 0-4 inches maximum

NOTICE: Remove finishing strips before firing appliance.

	FINISHING STRIP NOT USED
		(See Figure 13.7 for
		removal instructions)
	NON-COMBUSTIBLE
	FINISHING MATERIAL
		DOOR
FINISHING MATERIAL		FINISHING MATERIAL
Figure 13.6	Folio/CF Inside Fit

	8000 Models		6000 Models
	Inches	Millimeters	Inches	Millimeters
A	44-1/16	1119	37-1/16	941
B	35-15/16	913	34-1/16	865
C	44-5/16	1126	37-5/16	948
D	36-5/16	922	34-7/16	882

58	Heat & Glo • 6000C, 6000C-IPI, 8000C, 8000C-IPI • 2164-900 Rev. T • 9/12

Image 58

Heat & Glo LifeStyle 6000C manual Finishing Material Thickness 1-4 inches maximum, Models

Contents

HOT Surfaces What to do if you smell gasHot glass will cause burns Congratulations Homeowner Reference Information Table of Contents User Guide Finishing Appliance SetupTroubleshooting Reference Materials Limited Lifetime Warranty Hearth & Home Technologies Inc Limited Lifetime Warranty Limited Lifetime Warranty Warranty Conditions High Altitude Installations Tempered Glass SpecificationsBTU Specifications Listing and Code Approvals Electrical Codes Non-Combustible Materials SpecificationCombustible Materials Specification C22.1 Requirements for the Commonwealth of Massachusetts Operating Instructions User Guide Gas Fireplace SafetyYour Fireplace Fan Kit optional Fixed Glass AssemblyRemote Controls, Wall Controls and Wall Switches Clear Space Nine Hour Safety Shutdown Feature IPI Battery Tray/Battery InstallationModule Reset Control Module Operation What to do if YOU Smell GAS Lighting Instructions IPIFinal inspection by GAS Valve For Your Safety Read Before Lighting Lighting Instructions Lighting Instructions Standing Pilot Issue Solutions Frequently Asked QuestionsAfter Fireplace is Lit Glass Cleaning Maintenance and ServiceMaintenance Tasks-Homeowner Remote Control Venting Maintenance Tasks-Qualified Service TechnicianGasket Seal and Glass Assembly Inspection Logs Refractory, Grate and Valve Assembly Removal Base Refractory Burner Identification/Verification Notch Location Getting Started Typical Appliance System Inspect Appliance and Components Design and Installation ConsiderationsTools and Supplies Needed Any such action may cause a fire hazard 6000 Framing and ClearancesSelecting Appliance Location 8000 6000 Constructing the Appliance ChaseClearances 8000 Combustible Mantels Mantel and Wall ProjectionsCombustible Mantel Legs or Wall Projections Termination Locations Vent Termination Minimum Clearances Covered Alcove Applications = 9 inches U.S.A Vent Table Key Vent Information and DiagramsApproved Pipe Use of Elbows Vent pipe, if desired Vent Diagrams Top Vent Horizontal TerminationOne Elbow 6000C-IPI 8000C-IPI V1 Minimum H1 Maximum 6000C-IPI V1 Minimum H1 + H2 Maximum Top Vent Horizontal Termination Two ElbowsThree Elbows 8000C-IPI V1 Minimum H1 + H2 Maximum Break Top Vent Vertical Termination Maximum + V 2 Min Top Vent Vertical Termination Three Elbows H1 + H2 V1 + V2 Minimum H1 + H2 MaximumPage H1 Maximum V1 Minimum H1 + H2 Maximum Rear Vent Horizontal Termination Two ElbowsH1 Maximum V1 Minimum H2+ H3 H1+ H2+ H3 Max V1 Minimum H1 Maximum Rear Vent Vertical Termination One ElbowMinimum + H Maximum Rear Vent Vertical Termination Three Elbows V1 Minimum H1 + H2 + H3 Maximum 10 ft Clearances to Combustibles Prior to installing the gas applianceCoaxial to Colinear Venting Termination Cap Flue Damper Connecting the LINK-DV30B to the DV-46DVA-GCL adapter Connecting the DV-46DVA-GCL Adapter to Appliance Top VentRear Vent Wall Penetration Framing Vent Clearances and FramingPipe Clearances to Combustibles Combustible Wall Penetration Install the Ceiling Firestop Pipe DVP SLP Flat Ceiling Installation Install Attic Insulation ShieldInstalling the Optional Heat-ZoneGas Kit Vaulted Ceiling Installation Appliance Preparation Top Vent Rear Vent Cut the metal retaining band and fold the sides out Securing and Leveling the Appliance Installing the Non-combustible BoardHeader Assemble Vent Sections DVP Pipe Only Installing Vent Pipe DVP and SLP PipeAttach Vent to the Firebox Assembly Assemble Pipe Sections Assemble Vent Sections SLP Pipe Only Assemble Slip Sections Secure the Vent Sections Disassemble Vent Sections Install Decorative Ceiling Components SLP only Assemble and Install Storm Collar Install Metal Roof FlashingRoof Pitch Min. Ft Install Decorative Wall Components SLP only Install Vertical Termination CapHeat Shield Requirements for Horizontal Termination Install Horizontal Termination Cap DVP and SLP Pipe DVP-HPC1 DVP-HPC2 Gas Pressure Gas InformationFuel Conversion Gas Connection Standing Pilot Ignition System Wiring Wiring RequirementsIntelliFire Plus Ignition System Wiring Optional Accessories Requirements To Junction Electrical Service and Repair Junction Box Installation Wall Switch Installation for Fan Optional Finishing Facing Material Finishing Material Inch Thick or Less DoorsDoor FIT Finish Material See Thickness Finishing Material Thickness 0-4 inches maximum Finishing Material Thickness 1-4 inches maximumModels Removal of Finishing Strips Finishing Strips Removed Elevated Hearth Systems Appliance Setup 6000C, 6000C-IPI Install the Log Assembly Log Assembly LOGS-6CBottom view Logs # 2 LOG Contacts Grate Tines Install the Log Assembly Log Assembly LOGS-8C 8000C-IPILP, 8000CBV-IPI Horizontal Grate BAR Air Shutter Settings Install Trim and/or SurroundAir Shutter Setting 6000 8000 Symptom Possible Causes Corrective Action TroubleshootingStanding Pilot Ignition System Troubleshooting Symptom Possible Cause Corrective Action Shorts in the wiring IntelliFire Plus Ignition System Reference Materials Appliance Dimension DiagramLocation Inches Millimeters GAS Line Access R Left Side TOP View Front View Right View Vent Components Diagrams DVP-AS2 DVP-TRAP Horizontal Termination Cap DVP-TRAPFL RF6M RF12MBEK DVP-BEK2 COOL-ADDM DVP-TVHW DVP-FBHT PVI-SLP Optional Wire HarnessPower Vent Inline SLP-LPC DV-46DVA-GCL DVP-HRC-SS DVP-HRC-ZC-SS Horizontal Termination CAPLINK-DV30B DVP-2SL Adapter SLP Pipe SLP45SLP90 DVP-SLP24 DVP-2SL SLP-TRAPSLP-WT-BK SLP-DCF-BK SLP-CCS-BKSLK-SNKD SLP-TVHW Gas Fireplace DV Service PartsAt Depot Beginning Manufacturing Date Aug 8000C, 8000C-IPI 6000C-IPI 8000C-IPI 6000C Stocked8000C Standing Pilot Conversion Kits IPI Conversion Kits Contact Information