Heat & Glo LifeStyle 6000GLX-IPILP-S/-R, 6000GLX-IPI-S/-R manual

B. Vent Components Diagrams (continued)

8-1/8 in.

(206 mm)

15in.

(381 mm)

13 in.	Effective Length
13 in.
(330 mm)				5-1/2 in.				8-3/8 in.
(330 mm)	5-3/4 to 8-3/8 in.
	5-3/4 to 8-3/8 in.
	146 to 213 mm			140 mm				213 mm
	146 to 213 mm			140 mm				213 mm

					87°		3°

10-1/2 in.

267 mm

10-7/8 in.

276 mm

WARNING

Fire Risk.

•When using DVP-HRC-SS and DVP-HRC-ZC- SS termination caps on top vented ﬁreplaces, a 6 inch minimum vertical vent section is required

before installing ﬁrst elbow.

DVP-HRC-SS

DVP-HRC-ZC-SS

HORIZONTAL TERMINATION CAP

Figure 16.6 DVP vent components

Heat & Glo • 6000GLX-IPI-S/-R, 6000GLX-IPILP-S/-R • 2101-900 Rev. Q • 11/08

65

Image 65

Heat & Glo LifeStyle 6000GLX-IPILP-S/-R, 6000GLX-IPI-S/-R owner manual DVP-HRC-SS DVP-HRC-ZC-SS Horizontal Termination CAP

Contents

Hot glass will cause burns What to do if you smell gas Homeowner Reference Information Congratulations User Guide Table of Contents Troubleshooting Appliance SetupFinishing Reference Materials CONDITIONS, Exclusions & Limitation of Liability Limited Lifetime Warranty Listing and Code Approvals Requirements for the Commonwealth of Massachusetts Installation of Carbon Monoxide Detectors Your Fireplace Gas Fireplace SafetyOperating Instructions User Guide Remote Controls, Wall Controls and Wall Switches Fixed Glass AssemblyFan Kit optional Clear Space On position. The ON/OFF switch may Turn off all electric power to the applianceLighting Instructions IPI Final inspection by After Fireplace is Lit Frequently Asked Questions Maintenance Tasks-Homeowner Maintenance and ServiceGlass Cleaning Remote Control Gasket Seal and Glass Assembly Inspection Maintenance Tasks-Qualiﬁed Service TechnicianVenting Logs IPI Pilot Flame Patterns Typical Appliance System Getting Started Tools and Supplies Needed Design and Installation ConsiderationsInspect Appliance and Components Any such action may cause a ﬁre hazard Selecting Appliance Location Framing and Clearances Clearances Constructing the Appliance Chase Combustible Mantel Legs or Wall Projections Mantel and Wall ProjectionsCombustible Mantels Vent Termination Minimum Clearances Termination Locations Covered Alcove Applications Approved Pipe Vent Information and DiagramsVent Table Key Use of Elbows V1 Minimum H1 + H2 Maximum Vent Diagrams Top Vent Horizontal TerminationV1 Minimum H1 Maximum Min Max Top Vent Horizontal Termination Three Elbows Break Here Maximum + V 2 Min Top Vent Vertical TerminationTwo Elbows H1 + H2 V1 + V2 Minimum H1 + H2 Maximum Top Vent Vertical Termination Three ElbowsPage H1 Maximum V1 Minimum H2+ H3 H1+ H2+ H3 Max Rear Vent Horizontal Termination Two ElbowsH1 Maximum V1 Minimum H1 + H2 Maximum H1 + H2 Maximum V1 Minimum Rear Vent Vertical Termination One Elbow V1 Minimum H1 + H2 + H3 Rear Vent Vertical Termination Three Elbows Pipe Clearances to Combustibles Vent Clearances and FramingWall Penetration Framing Combustible Wall Penetration Pipe DVP SLP Install the Ceiling Firestop Installing the Optional Heat-Zone-Gas Kit Install Attic Insulation ShieldFlat Ceiling Installation Vaulted Ceiling Installation Proceed to . C Appliance PreparationChoosing the Top or Rear Vent Rear Vent Securing and Leveling the Appliance Installing the Non-combustible Board Attach Vent to the Firebox Assembly Installing Vent Pipe DVP and SLP PipeAssemble Vent Sections DVP Pipe Only Assemble Pipe Sections Assemble Slip Sections Assemble Vent Sections SLP Pipe Only Disassemble Vent Sections Secure the Vent Sections Install Decorative Ceiling Components SLP only Assemble and Install Storm Collar Install Metal Roof Flashing SLP-FS Install RF4-8 Heat Shield Requirements for Horizontal Termination Install Vertical Termination CapInstall Decorative Wall Components SLP only Refer to of this manual Install Horizontal Termination Cap DVP and SLP PipeAnsi Z223.1 and CAN/CGA-B149 installation codes Fuel Conversion Gas InformationGas Pressure Gas Connection Intelliﬁre Ignition System Wiring Wiring RequirementsOptional Accessories Requirements Electrical Information Intelliﬁre Pilot Ignition IPI Wiring Diagram Electrical Service and Repair Wall Switch Installation for Fan Optional Junction Box Installation Facing Material Finishing Finish Door FIT Material See Maximum Thickness Doors Appliance Setup Placement of Embers Ember Placement Install the Log Assembly Log Assembly LOGS-6000GLX LOGS-6000GLXLP 11 Front View 17 Front View Install Trim and/or Surround Install the MeshAir Shutter Setting Air Shutter Settings Intelliﬁre Ignition System TroubleshootingSymptom Possible Cause Corrective Action Ues to spark, and main Location Inches Millimeters Appliance Dimension DiagramReference Materials DVP vent components Vent Components Diagrams DVP vent components Horizontal Termination Cap Roof Flashing Multi-pak 13-3/4 11-7/8 349 mm 787 mm 13-1/4 367 mm 24-5/8 625 mm 27-1/2 127 mm302 mm 13-3/4 13-7/8 352 mm 349 mm DVP-TVHW DVP-HRC-SS DVP-HRC-ZC-SS Horizontal Termination CAP 165 mm 222 mm 235 mm 152 mm 168 mm 165 mmElbow 251 mm Black Snorkel Support Box-BlackCathedral Ceiling Vertical Termination Cap Service Parts Log Set Assembly At Depot Service Parts ListStocked 6000GLX-IPI-R,-S 6000GLX-IPI-R,S Contact Information