Manuals / Heat & Glo LifeStyle / Household Appliance / Indoor Fireplace

Heat & Glo LifeStyle BAY-40 B. Clearances, Fire Risk, 2 Clearances to Combustible Materials

Models: BAY-40

1 52

Download 52 pages 14.25 Kb

Page 10

Image 10

B. Clearances

WARNING

Fire Risk

•Comply with all minimum clearances to combustibles as speciﬁed.

•Framing or ﬁnishing material used on the front of, or in front of, the appliance closer than the minimums listed, must be constructed entirely of noncombustible materials (i.e., steel studs, concrete board, etc.).

Failure to comply may cause ﬁre.

Storm Collar

Roof Flashing

		2 in. (51 mm) min.
	2 in. min.	Attic
	(51 mm)	Attic
	(51 mm)	Insulation
		Insulation
	(attic)	Shield
	(attic)	Ceiling Firestop
		Ceiling Firestop
		(ceiling)
	2 in. (51 mm) min.	2 in. (51 mm) min.
		Offset/Return with
	Ceiling Firestop	hanger straps
		(ceiling)

2 in. (51 mm) min.

Must have 2 in. (51 mm)

minimum clearance

0 in. to level to header of standoffs

1/2 in. [13 mm] to back of appliance

1/2 in. (13 mm) to	0 in.
side of appliance	to floor

Figure 3.2 Clearances to Combustible Materials

10	Heat & Glo • Multi-Sided Woodburning Fireplace • 34977 Rev T • 11/07

Page 10

Image 10

Heat & Glo LifeStyle BAY-40 owner manual B. Clearances, Fire Risk, 2 Clearances to Combustible Materials

Contents

Owner’s Manual Models BAY-40, PIER-40 Multi-sided Woodburning FireplaceListing Label Information/Location Read this manual before installing or operating this ﬁreplacePlease retain this owner’s manual for future reference Date purchased/installed5 Chimney Assembly Table of Contents4 Installation of Fireplace 7 AccessoriesNot intended for use as a primary heat source Listing and Code ApprovalsA. Appliance Certiﬁcation Fire RiskB. Negative Pressure A. Design and Installation Considerations2 Getting Started Asphyxiation RiskWindward MarginalLocation Figure 2.1 Recommended Chimney LocationsC. Typical Fireplace System E. Inspect Fireplace and Components D. Tools and Supplies NeededFire Risk Explosion Risk A. Selecting Fireplace Location Framing and ClearancesFire Risk Fire Risk B. ClearancesFigure 3.2 Clearances to Combustible Materials Mantel C. Sidewalls/SurroundsD. Frame the Fireplace Mantel1. Fireplace and chimney enclosed in an exterior chase E. Construct the ChaseF. Chimney Requirements 2. Chimney offset through exterior wall and enclosed in chaseFire Risk Installation of FireplaceA. Install the Outside Air Kit Sharp EdgesLIFT TO OPEN Figure 4.3 Outside Combustion Air PlacementFigure 4.2 Outside Air Inlet Locations PULL TO OPENPlace the Protective Metal Hearth Strips B. Secure the FireplacePosition the Fireplace Level the Fireplace5 Chimney Assembly Fire Risk A. Chimney RequirementsDimensions reﬂect effective height Offsets/ReturnsSL1106 B. Using Offsets/ReturnsFire Risk SL1112When attic insulation D. Install the Ceiling FirestopsC. Assemble the Chimney Sections Fire RiskFire Risk ¨E. Install the Attic Insulation Shield¨ Figure 5.8 Install Attic Insulation Shield Below the Ceiling Figure 5.6 Prepare Attic Insulation ShieldStraps F. Double-check the Chimney AssemblyG. Secure the Chimney Ceiling Firestop Joint BandIf using decorative cap covers, this distance may 6 Complete the EnclosureA. Chimney Termination need to be increased. Refer to the installation instrucMark the Exit Point of the Roof Install the Roof FlashingInstall the Chimney Air Kit required in Canada ¨ Cut Out the Hole in the RoofFire Risk C. Install the Termination CapB. Chase Top Termination CapCap Base bracket screw Figure 6.7 Installing an ST1175 Square Termination CapFigure 6.8 Installing a TCT1175 Terra Cotta Cap cap inner flueAsphyxiation Risk AccessoriesA. Gas Log/Lighter Provisions Gas Code, ANSI Z223.1¨ Table 8 FinishingA. Hearth Extension Fire RiskCombustible Material B. Finishing MaterialFire Risk Non-Combustible MaterialE. Glass Doors C. MantelD. Sidewalls/Surrounds Fire RiskHigh temperatures may ignite clothing or other ﬂammable materials 9 Operating InstructionsA. General Information Fire RiskD. Flue Damper B. Outside AirC. Clear Space Near the Fireplace E. FirescreenFirewood G. GrateH. Wood Fuel MoistureI. Starting a Fire Fire Risk10 Troubleshooting A. Understanding Vent ProblemsSolutions B. Diagnostics and Problem SolvingDiagnostic Questions Diagnostic QuestionsSolutions I smell smoke in the house during operation. What’s causing that?Diagnostic Questions Diagnostic QuestionsA. Disposal of Ashes 11 Maintenance and Servicing the FireplaceB. Chimney Inspection/Cleaning C. Firebox RefractoryWhen cleaning glass door D. Maintenance Task ListE. Chimney Fire CleanA. Fireplace Dimensions 12 Reference MaterialsDescription B. Fireplace ComponentsCatalog # 52 in 1321 mm 16 in 406 mmC. Chimney Components Catalog #13 in 14-1/2 in368 mm Assembled Diameter 17 in./432 mm Height 24 in./610 mmCatalog # 15-3/4 in 400 mm14-3/4 in 375 mm Catalog #20-3/4 in. 527 mm 38-5/8 in 981 mm European Copper Caps21 in 533 mm 18-1/4 in. 464 mm 47-3/4 in 1213 mm41-1/8 in 1045 mm 24 inWoodburning Termination Cap Minimum Base DimensionsMinimum Base Dimensions ShroudBAY-40 Service PartsD. Service Parts Service Parts DiagramDescription of Part Service PartsBAY-40 Part Number Qty.reqService Parts Diagram PIER-40Service Parts Beginning Manufacturing Date N/A# Description of Part Service PartsPIER-40 PIER-40This page intentionally left blank Heat & Glo Multi-Sided Woodburning Fireplace 34977 Rev T 11/07E. Limited Warranty WARRANTY FOR HEAT & GLO FIREPLACESDO NOT DISCARD THIS MANUAL ¨ F. Contact InformationPlease contact your Heat & Glo dealer with any questions or concerns DO DISCARDNOT