Manuals / Heat & Glo LifeStyle / Household Appliance / Indoor Fireplace

Heat & Glo LifeStyle BAY-40 owner manual Service Parts, Description of Part, Part Number Qty.req

Models: BAY-40

1 52

Download 52 pages 14.25 Kb

Page 47

Description of Part

	Service Parts	BAY-40

	Service Parts List	Beginning Manufacturing Date: N/A
	Multi-Sided Woodburning Fireplace	Ending Manufacturing Date: 08/01/01

#	Description of Part	Part Number Qty.req.

1Top Standoff

2Starter Section Assembly

3Damper Assembly

4Front Door Support

5Side Door Support

6Grate

7End Retainer Assembly

8Grate Retainer (for End Retainer Assembly)

9Back Refractory

10Side Refractory

11Hearth Refractory

12Front Ashlip

13Left Side Ashlip

14Right Side Ashlip Nailing Flange Firescreen Rod Firescreen Assembly Screen Handle Damper Control Damper Weight

Door Track (for bottom) Door Track (for top) Grate Retainer

Side Refractory Bracket Refractory Bracket Outside Air Door Assembly Air Kit

Fastener Pack Plate Assembly Long Cable Tie

Air Kit Installation Instructions Outside Air Shield

Strip Protector

BAY-40 Installation Instructions and Owner’s Manual

11864i	4
22072B	1
34515	1
4012-035	1
23954	2
GR3	1
13929A	2
13294B	4
27856	1
27857	2
13213A	1
13214A	1
13827A	1
13828A	1
12692	4
11866B	2
12267	2
4021-149	1ea.
13229	1
19785A	1
4012-002	1
15425	1
13834B	2
13831C	2
13896B	2
13268A	1
AK17	1
12010B	1
19081A	1
19954A	2
31168	1
33271	1
18320	4
34977	1

Heat & Glo • Multi-Sided Woodburning Fireplace • 34977 Rev T • 11/07

47

Image 47

Heat & Glo LifeStyle BAY-40 owner manual Service Parts, Description of Part, Part Number Qty.req

Contents

Models BAY-40, PIER-40 Multi-sided Woodburning Fireplace Owner’s ManualDate purchased/installed Read this manual before installing or operating this ﬁreplacePlease retain this owner’s manual for future reference Listing Label Information/Location7 Accessories Table of Contents4 Installation of Fireplace 5 Chimney AssemblyFire Risk Listing and Code ApprovalsA. Appliance Certiﬁcation Not intended for use as a primary heat sourceAsphyxiation Risk A. Design and Installation Considerations2 Getting Started B. Negative PressureFigure 2.1 Recommended Chimney Locations MarginalLocation WindwardC. Typical Fireplace System Fire Risk Explosion Risk D. Tools and Supplies NeededE. Inspect Fireplace and Components Fire Risk Framing and ClearancesA. Selecting Fireplace Location Figure 3.2 Clearances to Combustible Materials B. ClearancesFire Risk Mantel C. Sidewalls/SurroundsD. Frame the Fireplace Mantel2. Chimney offset through exterior wall and enclosed in chase E. Construct the ChaseF. Chimney Requirements 1. Fireplace and chimney enclosed in an exterior chaseSharp Edges Installation of FireplaceA. Install the Outside Air Kit Fire RiskPULL TO OPEN Figure 4.3 Outside Combustion Air PlacementFigure 4.2 Outside Air Inlet Locations LIFT TO OPENLevel the Fireplace B. Secure the FireplacePosition the Fireplace Place the Protective Metal Hearth Strips5 Chimney Assembly Offsets/Returns A. Chimney RequirementsDimensions reﬂect effective height Fire RiskSL1112 B. Using Offsets/ReturnsFire Risk SL1106Fire Risk D. Install the Ceiling FirestopsC. Assemble the Chimney Sections When attic insulationFigure 5.6 Prepare Attic Insulation Shield ¨E. Install the Attic Insulation Shield¨ Figure 5.8 Install Attic Insulation Shield Below the Ceiling Fire RiskCeiling Firestop Joint Band F. Double-check the Chimney AssemblyG. Secure the Chimney Strapsneed to be increased. Refer to the installation instruc 6 Complete the EnclosureA. Chimney Termination If using decorative cap covers, this distance may¨ Cut Out the Hole in the Roof Install the Roof FlashingInstall the Chimney Air Kit required in Canada Mark the Exit Point of the RoofTermination Cap C. Install the Termination CapB. Chase Top Fire Riskcap inner flue Figure 6.7 Installing an ST1175 Square Termination CapFigure 6.8 Installing a TCT1175 Terra Cotta Cap Cap Base bracket screwGas Code, ANSI Z223.1 AccessoriesA. Gas Log/Lighter Provisions Asphyxiation RiskFire Risk 8 FinishingA. Hearth Extension ¨ TableNon-Combustible Material B. Finishing MaterialFire Risk Combustible MaterialFire Risk C. MantelD. Sidewalls/Surrounds E. Glass DoorsFire Risk 9 Operating InstructionsA. General Information High temperatures may ignite clothing or other ﬂammable materialsE. Firescreen B. Outside AirC. Clear Space Near the Fireplace D. Flue DamperMoisture G. GrateH. Wood Fuel FirewoodFire Risk I. Starting a FireA. Understanding Vent Problems 10 TroubleshootingDiagnostic Questions B. Diagnostics and Problem SolvingDiagnostic Questions SolutionsDiagnostic Questions I smell smoke in the house during operation. What’s causing that?Diagnostic Questions SolutionsC. Firebox Refractory 11 Maintenance and Servicing the FireplaceB. Chimney Inspection/Cleaning A. Disposal of AshesClean D. Maintenance Task ListE. Chimney Fire When cleaning glass door12 Reference Materials A. Fireplace Dimensions52 in 1321 mm 16 in 406 mm B. Fireplace ComponentsCatalog # DescriptionCatalog # C. Chimney ComponentsAssembled Diameter 17 in./432 mm Height 24 in./610 mm 14-1/2 in368 mm 13 inCatalog # 15-3/4 in 400 mm14-3/4 in 375 mm Catalog #24 in European Copper Caps21 in 533 mm 18-1/4 in. 464 mm 47-3/4 in 1213 mm41-1/8 in 1045 mm 20-3/4 in. 527 mm 38-5/8 in 981 mmShroud Minimum Base DimensionsMinimum Base Dimensions Woodburning Termination CapService Parts Diagram Service PartsD. Service Parts BAY-40Part Number Qty.req Service PartsBAY-40 Description of PartBeginning Manufacturing Date N/A PIER-40Service Parts Service Parts DiagramPIER-40 Service PartsPIER-40 # Description of PartHeat & Glo Multi-Sided Woodburning Fireplace 34977 Rev T 11/07 This page intentionally left blankWARRANTY FOR HEAT & GLO FIREPLACES E. Limited WarrantyDO DISCARDNOT ¨ F. Contact InformationPlease contact your Heat & Glo dealer with any questions or concerns DO NOT DISCARD THIS MANUAL