Manuals / Heat & Glo LifeStyle / Household Appliance / Burner

Heat & Glo LifeStyle PIER-36TRLP-IPI, PIER-36TR-IPI Getting Started, A. Typical Appliance System

Models: PIER-36TR-IPI PIER-36TRLP-IPI ST-36TRLP-IPI ST-36TR-IPI

1 85

Download 85 pages 56.19 Kb

Page 16

Getting Started

4	Getting Started	Installer Guide

A. Typical Appliance System

NOTICE: Illustrations and photos reﬂect typical installations and are for design purposes only. Illustrations/diagrams are not drawn to scale. Actual product may vary from pictures in manual

HORIZONTAL

TERMINATION CAP (SECTION 10.M )

FRAMING/HEADER (SECTION 5.B)

Note: Dual venting configurations ARE NOT allowed. Appliance MUST be vented EITHER vertically OR horizontally.

NON-COMBUSTIBLE ROOF FLASHING

MAINTAINS MINIMUM CLEARANCE

AROUND PIPE (SECTION 10.G)

VERTICAL TERMINATION CAP (SECTION 10.J)

STORM COLLAR (SECTION 10.H)

VENT PIPE PENETRATES ROOF

PREFERABLY WITHOUT AFFECTING

ROOF RAFTERS (SECTION 8.C )

ATTIC INSULATION SHIELD (NOT

SHOWN) MUST BE USED HERE

TO KEEP INSULATION AWAY

FROM VENT PIPE IF ATTIC IS

INSULATED (SECTION 8.D )

VENT PIPE (SECTION 9 and 10)

FRAMING HEADED OFF

IN CEILING JOISTS

(SECTION 8.C)

CEILING FIRESTOP

ON FLOOR OF ATTIC (SECTION 8.C)

WALL SWITCH

SECTION 12.E.

GAS LINE

(SECTION 11.C)

HEARTH EXTENSION

SURROUND

MANTEL AND MANTEL LEG (SECTION 5.D)

Figure 4.1 Typical System

16	Heat & Glo • ST-36TR-IPI, PIER-36TR-IPI • 2176-900 Rev. F • 8/11

Image 16

Heat & Glo LifeStyle PIER-36TRLP-IPI Getting Started, A. Typical Appliance System, Installer Guide, 1 Typical System

Contents

What to do if you smell gas Models ST-36TR-IPI ST-36TRLP-IPI PIER-36TR-IPI PIER-36TRLP-IPIOwner’s Manual A. Congratulations Homeowner Reference InformationRead this manual before installing or operating this appliance Please retain this owner’s manual for future referenceTable of Contents Safety Alert KeyInstaller Guide 7 Vent Information and Diagrams14 Appliance Setup 15 Troubleshooting = Contains updated information 13 Finishing B. Limited Lifetime Warranty Hearth & Home Technologies Inc LIMITED LIFETIME WARRANTYWARRANTY COVERAGE WARRANTY PERIOD B. Limited Lifetime Warranty continued WARRANTY CONDITIONSWARRANTY EXCLUSIONS This warranty is void ifD. High Altitude Installations 1 Listing and Code ApprovalsA. Appliance Certiﬁcation B. Tempered Glass SpeciﬁcationsH. Requirements for the Commonwealth of Massachusetts Installation of Carbon Monoxide DetectorsApproved Carbon Monoxide Detectors Signage2 Operating Instructions User Guide A. Gas Fireplace SafetyB. Your Fireplace Blower Installation F. Fixed Glass AssemblyG. Remote Controls, Wall Controls and Wall Switches C. Blower Kit optionalFOR YOUR SAFETY READ BEFORE LIGHTING LIGHTING INSTRUCTIONS IPITO TURN OFF GAS TO APPLIANCE I. Lighting Instructions IPIK. Frequently Asked Questions J. After Fireplace is LitISSUE SOLUTIONS3 Maintenance and Service A. Maintenance Tasks-HomeownerGlass Cleaning Remote ControlEmber Light Replacement B. Maintenance Tasks-Qualiﬁed Service TechnicianGasket Seal and Glass Assembly Inspection LogsFrequency Annually Burner Ignition and OperationFigure 3.4 IPI Pilot Flame Patterns Getting Started A. Typical Appliance SystemInstaller Guide Figure 4.1 Typical SystemC. Tools and Supplies Needed B. Design and Installation ConsiderationsD. Inspect Appliance and Components 5 Framing and Clearances A. Selecting Appliance Location36 in 36 inB. Constructing the Appliance Chase C. ClearancesC B D E I H GPIER-36TR-IPI InchesD. Mantel and Wall Projections See-Through Combustible MantelPIER Combustible Mantel See-Through Non-Combustible MantelTOP VIEW 1/2 inFIREPLACE 2-3/46 Termination Locations A. Vent Termination Minimum ClearancesRoof Pitch H Min. FtX = AIR SUPPLY INLET = AREA WHERE TERMINAL IS NOT PERMITTED Covered Alcove ApplicationsLocal codes or regulations may require different clearances Vent system termination is NOT permitted in screened porchesB. Continue Adding Vent Components C. Install Support BracketsTo Install the Heat Shield 7 Vent Information and Diagrams A. Approved PipeB. Vent Table Key C. Use of ElbowsE. Vent Diagrams Note The Multi-Sided series ﬁreplaces can adaptto SLP series vent pipe, if desired 1. Top Vent - Horizontal Termination - continuedOne Elbow Two Elbows1. Top Vent - Horizontal Termination - continued V1 Minimum1. Top Vent - Horizontal Termination Three Elbowscontinued H2 V2V1 = 3 ft. Min. 914 mm 2. Top Vent - Vertical Termination No Elbow V1 = 60 ft. Max. 18.3 mExhaust restrictor Instructions BREAK HERE Two Elbows Three ElbowsH 1 Maximum V 1 + V 2 Minimum3. Rear Vent - Horizontal Termination No Elbow H1 = 16 in. 406 mm MaximumOne 45 Elbow Heat & Glo ST-36TR-IPI, PIER-36TR-IPI 2176-900 Rev. F 8/113. Rear Vent - Horizontal Termination - continued Two ElbowsThree Elbows V1 H14. Rear Vent - Vertical Termination One Elbow Two ElbowsV1 Minimum H1 Maximum4. Rear Vent - Vertical Termination - continued Three ElbowsThree Elbows H1 Maximum8 Vent Clearances and Framing A. Pipe Clearances to CombustiblesB. Wall Penetration Framing Between ceiling ﬁrestops Between wall shield ﬁrestopsC. Vertical Penetration Framing Flat Ceiling Installation D. Install Attic Insulation ShieldVaulted Ceiling Installation 9 Appliance Preparation A. Top VentNOTICE Once the vent cap has been removed it CANNOT be reattached Proceed to Section 9. CB. Rear Vent Figure 9.5 Cut the metal retaining bandFigure 9.6 Remove the seal cap NOTICE Once the vent cap has been removed it CANNOT be reattachedC. Securing and Leveling the Appliance WARNING! Risk of Fire! Prevent contact withSagging or loose insulation Insulation backing or plastic Framing and other combustible materials10 Installing Vent Pipe DVP and SLP Pipe A. Assemble Vent Sections DVP Pipe OnlyAttach Vent to the Firebox Assembly Assemble Pipe Sections DVP Pipe OnlyB. Assemble Vent Sections SLP Pipe Only C. Assemble Slip SectionsPilot hole Only outer pipes are sealed, sealing the inner ﬂue is not requiredD. Secure the Vent Sections E. Disassemble Vent SectionsF. Install Decorative Ceiling Components SLP only LEVEL CATHEDRAL CEILING SUPPORT BOXCUT HOLE 1/8 in. 3 mm GREATER IN SIZE THAN PATTERN OF SUPPORT BOX AS IT IS PROJECTED ONTO ROOF LINEG. Install Metal Roof Flashing H. Assemble and Install Storm CollarCAULK CAUTION! Risk of Cuts, Abrasions or Flying DebrisI. Install Vertical Termination Cap J. Install Decorative Wall Components SLP onlyK. Heat Shield Requirements for Horizontal Termination Heat shields must overlap 1-1/2 in. 38 mm mini- mum1-1/2 38 mm minimum overlap of ﬂue telescoping section is required L. Install Horizontal Termination Cap DVP and SLP PipeFailure to maintain overlap may cause overheating and ﬁre 11 Gas Information A. Fuel ConversionB. Gas Pressure C. Gas ConnectionA. Wiring Requirements D. Junction Box InstallationB. IntelliFire Ignition System Wiring C. Electrical Service and RepairPrecautions E. WSK-MLT Multifunction Wall SwitchDetermine Location Wiring the Wall Switch Figure 12.2 Intelliﬁre IPI Wiring DiagramF. Install the Flame Solenoid G. Connect the Temperature Sensor Switch for Fan optionalI. Setting Flame Height/Manifold Pressure J. Wall Switch Button OperationH. WSK-MLT Operating Instructions Temperature ButtonSet Temperature Button Operation Under Battery PowerUp and Down Arrows Auxiliary ButtonA. Splatter Guard 13 FinishingTo install the Splatter Guard To Close the Lower Access Panel Figure 13.7 Prepare to Open Lower Access PanelFigure 13.8 Opening Lower Access Panel Figure 13.10 Splatter Guard with Lower Access Panel OpenB. Mantel and Wall Projections Dimensions of CombustiblesDimensions of Combustibles Dimensions of Non-CombustiblesC. Facing Material TOP VIEW1/2 in FIREPLACED. Finishing Material ST-36TR-IPIPIER-36TR-IPI FINISH MATERIALFigure 13.22 Pier Door Finishing Heat & Glo ST-36TR-IPI, PIER-36TR-IPI 2176-900 Rev. F 8/1133-5/8 in 37-1/4 inE. Elevated Hearth Systems Note 3. Dimensions assume use of a 3/4 in. Hearth Pad14 Appliance Setup A. Remove Fixed Glass AssemblyC. Clean the Appliance D. AccessoriesPlacing the Ember Material Log Set Assembly LOGS-MSR F. Install the Log AssemblyPILOT ASSEMBLY ASSEMBLY3 2 5 4 SHARP NOTCH4 3/4 IN SHARP NOTCH3 2 54 1 3 4 6FLAT AREA NotchG. Fixed Glass Assembly H. Install Trim Kits and SurroundsI. Air Shutter Setting Removing Fixed Glass Assembly15 Troubleshooting A. IntelliFire Ignition SystemSymptom Possible CauseIntelliFire Ignition System - continued SymptomPossible Cause Corrective ActionA. Appliance Dimension Diagram 16 Reference MaterialsLocation InchesACCESS GAS LINE ACCESS G LEFT VIEWELECTRICAL C D NB. Vent Components Diagrams Height 24 in./610 mmDVP-AS2 Heat & GloB. Vent Components Diagrams continued DVP-TRAP1DVP-TRAP2 DVP-TRAPK1B. Vent Components Diagrams continued 31 in787 mm 13-1/4 inB. Vent Components Diagrams continued 3-7/8 in98 mm 10-1/2 inDVP-HRC-SS B. Vent Components Diagrams continuedOptional Wire Harness DESCRIPTIONB. Vent Components Diagrams continued SLP4545 Elbow SLP90 90 ElbowB. Vent Components Diagrams continued ASSEMBLYSLP-DCF-BK SLK-SNKDC. Service Parts Log Set AssemblyST-36TR-IPI at DepotPIER-36TR-IPI StockedC. Service Parts Log Set Assembly#17 Valve Assembly C. Service PartsPIER-36TR, ST-36TR-IPI at DepotC. Service Parts List ST-36TR-IPI, PIER-36TR-IPIStocked at DepotD. Contact Information DO NOT DISCARD THIS MANUALPlease contact your Heat & Glo dealer with any questions or concerns For the location of your nearest Heat & Glo dealer