Manuals / Heat & Glo LifeStyle / Household Appliance / Burner

Heat & Glo LifeStyle PIER-36TRLP-IPI C. Facing Material, Top View, 1/2 in, Fireplace, 2-3/4, 1 in

Models: PIER-36TR-IPI PIER-36TRLP-IPI ST-36TRLP-IPI ST-36TR-IPI

1 85

Download 85 pages 56.19 Kb

Page 60

C. Facing Material

TOP VIEW	1/2 in.
	Min.

FIREPLACE			2-3/4
OPENING			in. Min.

		Unlimited

	1 in.
	1 in.
	Max.

Note: Clearance from opening to perpendicular wall.

Figure 13.16 Combustible Mantel Leg or Wall Projections (Acceptable on both sides of opening)

C. Facing Material

•Metal front faces may be covered with non-combustible materials only.

•Facing and/or ﬁnishing materials must not interfere with air ﬂow through louvers, operation of louvers or doors, or access for service.

•Facing and/or ﬁnishing materials must never overhang into the glass opening.

•Observe all clearances when applying combustible materials.

•Seal joints between the ﬁnished wall and appliance top and sides using a 300 °F minimum sealant. Refer to Figure 13.17.

WARNING! Risk of Fire! DO NOT apply combustible materials beyond the minimum clearances. Comply with all minimum clearances to combustibles as speciﬁed in this manual. Overlapping materials could ignite and will interfere with proper operation of doors and louvers.

Finish wall material may be combustible - Top and Sides

	0 in.
0 in.	0 in.

High Temperature Sealant (300° F/149° C min.)

Top and Side Seal Joint

Figure 13.17 Noncombustible Facing Diagram

60	Heat & Glo • ST-36TR-IPI, PIER-36TR-IPI • 2176-900 Rev. F • 8/11

Image 60

Heat & Glo LifeStyle PIER-36TRLP-IPI C. Facing Material, Top View, 1/2 in, Fireplace, 2-3/4, Opening, Unlimited, 1 in

Contents

Models ST-36TR-IPI ST-36TRLP-IPI PIER-36TR-IPI PIER-36TRLP-IPI What to do if you smell gasOwner’s Manual A. Congratulations Homeowner Reference InformationRead this manual before installing or operating this appliance Please retain this owner’s manual for future referenceTable of Contents Safety Alert KeyInstaller Guide 7 Vent Information and Diagrams14 Appliance Setup 15 Troubleshooting = Contains updated information 13 Finishing B. Limited Lifetime Warranty Hearth & Home Technologies Inc LIMITED LIFETIME WARRANTYWARRANTY COVERAGE WARRANTY PERIOD B. Limited Lifetime Warranty continued WARRANTY CONDITIONSWARRANTY EXCLUSIONS This warranty is void ifD. High Altitude Installations 1 Listing and Code ApprovalsA. Appliance Certiﬁcation B. Tempered Glass SpeciﬁcationsH. Requirements for the Commonwealth of Massachusetts Installation of Carbon Monoxide DetectorsApproved Carbon Monoxide Detectors SignageA. Gas Fireplace Safety 2 Operating Instructions User GuideB. Your Fireplace Blower Installation F. Fixed Glass AssemblyG. Remote Controls, Wall Controls and Wall Switches C. Blower Kit optionalFOR YOUR SAFETY READ BEFORE LIGHTING LIGHTING INSTRUCTIONS IPITO TURN OFF GAS TO APPLIANCE I. Lighting Instructions IPIK. Frequently Asked Questions J. After Fireplace is LitISSUE SOLUTIONS3 Maintenance and Service A. Maintenance Tasks-HomeownerGlass Cleaning Remote ControlEmber Light Replacement B. Maintenance Tasks-Qualiﬁed Service TechnicianGasket Seal and Glass Assembly Inspection LogsBurner Ignition and Operation Frequency AnnuallyFigure 3.4 IPI Pilot Flame Patterns Getting Started A. Typical Appliance SystemInstaller Guide Figure 4.1 Typical SystemB. Design and Installation Considerations C. Tools and Supplies NeededD. Inspect Appliance and Components 5 Framing and Clearances A. Selecting Appliance Location36 in 36 inB. Constructing the Appliance Chase C. ClearancesC B D E I H GPIER-36TR-IPI InchesD. Mantel and Wall Projections See-Through Combustible MantelPIER Combustible Mantel See-Through Non-Combustible MantelTOP VIEW 1/2 inFIREPLACE 2-3/46 Termination Locations A. Vent Termination Minimum ClearancesRoof Pitch H Min. FtX = AIR SUPPLY INLET = AREA WHERE TERMINAL IS NOT PERMITTED Covered Alcove ApplicationsLocal codes or regulations may require different clearances Vent system termination is NOT permitted in screened porchesC. Install Support Brackets B. Continue Adding Vent ComponentsTo Install the Heat Shield 7 Vent Information and Diagrams A. Approved PipeB. Vent Table Key C. Use of ElbowsE. Vent Diagrams Note The Multi-Sided series ﬁreplaces can adaptto SLP series vent pipe, if desired 1. Top Vent - Horizontal Termination - continuedOne Elbow Two Elbows1. Top Vent - Horizontal Termination - continued V1 Minimum1. Top Vent - Horizontal Termination Three Elbowscontinued H2 V22. Top Vent - Vertical Termination No Elbow V1 = 60 ft. Max. 18.3 m V1 = 3 ft. Min. 914 mmExhaust restrictor Instructions BREAK HERE Two Elbows Three ElbowsH 1 Maximum V 1 + V 2 Minimum3. Rear Vent - Horizontal Termination No Elbow H1 = 16 in. 406 mm MaximumOne 45 Elbow Heat & Glo ST-36TR-IPI, PIER-36TR-IPI 2176-900 Rev. F 8/113. Rear Vent - Horizontal Termination - continued Two ElbowsThree Elbows V1 H14. Rear Vent - Vertical Termination One Elbow Two ElbowsV1 Minimum H1 Maximum4. Rear Vent - Vertical Termination - continued Three ElbowsThree Elbows H1 Maximum8 Vent Clearances and Framing A. Pipe Clearances to CombustiblesB. Wall Penetration Framing Between ceiling ﬁrestops Between wall shield ﬁrestopsC. Vertical Penetration Framing D. Install Attic Insulation Shield Flat Ceiling InstallationVaulted Ceiling Installation 9 Appliance Preparation A. Top VentNOTICE Once the vent cap has been removed it CANNOT be reattached Proceed to Section 9. CB. Rear Vent Figure 9.5 Cut the metal retaining bandFigure 9.6 Remove the seal cap NOTICE Once the vent cap has been removed it CANNOT be reattachedC. Securing and Leveling the Appliance WARNING! Risk of Fire! Prevent contact withSagging or loose insulation Insulation backing or plastic Framing and other combustible materials10 Installing Vent Pipe DVP and SLP Pipe A. Assemble Vent Sections DVP Pipe OnlyAttach Vent to the Firebox Assembly Assemble Pipe Sections DVP Pipe OnlyB. Assemble Vent Sections SLP Pipe Only C. Assemble Slip SectionsPilot hole Only outer pipes are sealed, sealing the inner ﬂue is not requiredD. Secure the Vent Sections E. Disassemble Vent SectionsF. Install Decorative Ceiling Components SLP only LEVEL CATHEDRAL CEILING SUPPORT BOXCUT HOLE 1/8 in. 3 mm GREATER IN SIZE THAN PATTERN OF SUPPORT BOX AS IT IS PROJECTED ONTO ROOF LINEG. Install Metal Roof Flashing H. Assemble and Install Storm CollarCAULK CAUTION! Risk of Cuts, Abrasions or Flying DebrisI. Install Vertical Termination Cap J. Install Decorative Wall Components SLP onlyK. Heat Shield Requirements for Horizontal Termination Heat shields must overlap 1-1/2 in. 38 mm mini- mumL. Install Horizontal Termination Cap DVP and SLP Pipe 1-1/2 38 mm minimum overlap of ﬂue telescoping section is requiredFailure to maintain overlap may cause overheating and ﬁre 11 Gas Information A. Fuel ConversionB. Gas Pressure C. Gas ConnectionA. Wiring Requirements D. Junction Box InstallationB. IntelliFire Ignition System Wiring C. Electrical Service and RepairE. WSK-MLT Multifunction Wall Switch PrecautionsDetermine Location Wiring the Wall Switch Figure 12.2 Intelliﬁre IPI Wiring DiagramF. Install the Flame Solenoid G. Connect the Temperature Sensor Switch for Fan optionalI. Setting Flame Height/Manifold Pressure J. Wall Switch Button OperationH. WSK-MLT Operating Instructions Temperature ButtonSet Temperature Button Operation Under Battery PowerUp and Down Arrows Auxiliary Button13 Finishing A. Splatter GuardTo install the Splatter Guard To Close the Lower Access Panel Figure 13.7 Prepare to Open Lower Access PanelFigure 13.8 Opening Lower Access Panel Figure 13.10 Splatter Guard with Lower Access Panel OpenB. Mantel and Wall Projections Dimensions of CombustiblesDimensions of Combustibles Dimensions of Non-CombustiblesC. Facing Material TOP VIEW1/2 in FIREPLACED. Finishing Material ST-36TR-IPIPIER-36TR-IPI FINISH MATERIALFigure 13.22 Pier Door Finishing Heat & Glo ST-36TR-IPI, PIER-36TR-IPI 2176-900 Rev. F 8/1133-5/8 in 37-1/4 inE. Elevated Hearth Systems Note 3. Dimensions assume use of a 3/4 in. Hearth Pad14 Appliance Setup A. Remove Fixed Glass AssemblyC. Clean the Appliance D. AccessoriesPlacing the Ember Material Log Set Assembly LOGS-MSR F. Install the Log AssemblyPILOT ASSEMBLY ASSEMBLY3 2 5 4 SHARP NOTCH4 3/4 IN SHARP NOTCH3 2 54 1 3 4 6FLAT AREA NotchG. Fixed Glass Assembly H. Install Trim Kits and SurroundsI. Air Shutter Setting Removing Fixed Glass Assembly15 Troubleshooting A. IntelliFire Ignition SystemSymptom Possible CauseIntelliFire Ignition System - continued SymptomPossible Cause Corrective ActionA. Appliance Dimension Diagram 16 Reference MaterialsLocation InchesACCESS GAS LINE ACCESS G LEFT VIEWELECTRICAL C D NB. Vent Components Diagrams Height 24 in./610 mmDVP-AS2 Heat & GloB. Vent Components Diagrams continued DVP-TRAP1DVP-TRAP2 DVP-TRAPK1B. Vent Components Diagrams continued 31 in787 mm 13-1/4 inB. Vent Components Diagrams continued 3-7/8 in98 mm 10-1/2 inDVP-HRC-SS B. Vent Components Diagrams continuedOptional Wire Harness DESCRIPTIONB. Vent Components Diagrams continued SLP4545 Elbow SLP90 90 ElbowB. Vent Components Diagrams continued ASSEMBLYSLP-DCF-BK SLK-SNKDC. Service Parts Log Set AssemblyST-36TR-IPI at DepotPIER-36TR-IPI StockedC. Service Parts Log Set Assembly#17 Valve Assembly C. Service PartsPIER-36TR, ST-36TR-IPI at DepotC. Service Parts List ST-36TR-IPI, PIER-36TR-IPIStocked at DepotD. Contact Information DO NOT DISCARD THIS MANUALPlease contact your Heat & Glo dealer with any questions or concerns For the location of your nearest Heat & Glo dealer