Manuals / Heat & Glo LifeStyle / Household Appliance / Burner

Heat & Glo LifeStyle ST-36TRLP-IPI, PIER-36TRLP-IPI, PIER-36TR-IPI F. Install the Flame Solenoid

Models: PIER-36TR-IPI PIER-36TRLP-IPI ST-36TRLP-IPI ST-36TR-IPI

1 85

Download 85 pages 56.19 Kb

Page 54

F. Install the Flame Solenoid

BULB SOCKET

ASSEMBLY (3)

BLK

WHT

	EMBER LIGHT
	CONNECTOR BLOCK
WHT	BLK
	WHT

BLK

Figure 12.3 Ember Light Connector Block Detail

F. Install the Flame Solenoid

•Remove the screw and knob from the variable regulator and discard.

•Remove the nut from the regulator and discard.

•Remove the bag containing a washer and blue and red plungers from the side of the ﬂame control solenoid.

•Place washer on ﬂame control solenoid.

•Insert the correct plunger (blue - natural gas, red - propane) into the ﬂame control solenoid.

•Thread the ﬂame control solenoid with correct plunger into the thread hole in the variable regulator. Turn into valve approximately two full turns. Do not tighten or damage may occur.

•Connect orange wires from control box to the ﬂame control solenoid.

G.Connect the Temperature Sensor Switch for Fan (optional)

•Find the two yellow wires from the WSK-MLT control box and disconnect them.

•Connect one yellow wire to one jumper wire hanging from the thermodisc.

•Connect the other yellow wire to remaining jumper wire hanging from thermodisc.

•See Figure 12.2 for wiring diagram.

GAS CONTROL

VALVE

WASHER

VARIABLE

REGULATOR

VARIABLE

REGULATOR

KNOB

SCREW

NUT

WASHER

FLAME CONTROL	VARIABLE
SOLENOID	REGULATOR

PLUNGER

SOLENOID

JAM NUT

Figure 12.4 Install the Flame Solenoid

54	Heat & Glo • ST-36TR-IPI, PIER-36TR-IPI • 2176-900 Rev. F • 8/11

Image 54

Heat & Glo LifeStyle ST-36TRLP-IPI, PIER-36TRLP-IPI, PIER-36TR-IPI, ST-36TR-IPI owner manual F. Install the Flame Solenoid

Contents

Models ST-36TR-IPI ST-36TRLP-IPI PIER-36TR-IPI PIER-36TRLP-IPI What to do if you smell gasOwner’s Manual Read this manual before installing or operating this appliance A. CongratulationsHomeowner Reference Information Please retain this owner’s manual for future referenceInstaller Guide Table of ContentsSafety Alert Key 7 Vent Information and Diagrams = Contains updated information 14 Appliance Setup15 Troubleshooting 13 FinishingWARRANTY COVERAGE  B. Limited Lifetime WarrantyHearth & Home Technologies Inc LIMITED LIFETIME WARRANTY WARRANTY PERIODWARRANTY EXCLUSIONS  B. Limited Lifetime Warranty continuedWARRANTY CONDITIONS This warranty is void ifA. Appliance Certiﬁcation D. High Altitude Installations1 Listing and Code Approvals B. Tempered Glass SpeciﬁcationsApproved Carbon Monoxide Detectors H. Requirements for the Commonwealth of MassachusettsInstallation of Carbon Monoxide Detectors SignageA. Gas Fireplace Safety 2 Operating Instructions User GuideB. Your Fireplace G. Remote Controls, Wall Controls and Wall Switches Blower InstallationF. Fixed Glass Assembly C. Blower Kit optionalTO TURN OFF GAS TO APPLIANCE FOR YOUR SAFETY READ BEFORE LIGHTINGLIGHTING INSTRUCTIONS IPI I. Lighting Instructions IPIISSUE K. Frequently Asked QuestionsJ. After Fireplace is Lit SOLUTIONSGlass Cleaning 3 Maintenance and ServiceA. Maintenance Tasks-Homeowner Remote ControlGasket Seal and Glass Assembly Inspection Ember Light ReplacementB. Maintenance Tasks-Qualiﬁed Service Technician LogsBurner Ignition and Operation Frequency AnnuallyFigure 3.4 IPI Pilot Flame Patterns Installer Guide Getting StartedA. Typical Appliance System Figure 4.1 Typical SystemB. Design and Installation Considerations C. Tools and Supplies NeededD. Inspect Appliance and Components 36 in 5 Framing and ClearancesA. Selecting Appliance Location 36 inB. Constructing the Appliance Chase C. ClearancesPIER-36TR-IPI C B DE I H G InchesPIER Combustible Mantel D. Mantel and Wall ProjectionsSee-Through Combustible Mantel See-Through Non-Combustible MantelFIREPLACE TOP VIEW1/2 in 2-3/4Roof Pitch 6 Termination LocationsA. Vent Termination Minimum Clearances H Min. FtLocal codes or regulations may require different clearances X = AIR SUPPLY INLET = AREA WHERE TERMINAL IS NOT PERMITTEDCovered Alcove Applications Vent system termination is NOT permitted in screened porchesC. Install Support Brackets B. Continue Adding Vent ComponentsTo Install the Heat Shield B. Vent Table Key 7 Vent Information and DiagramsA. Approved Pipe C. Use of Elbowsto SLP series vent pipe, if desired E. Vent DiagramsNote The Multi-Sided series ﬁreplaces can adapt 1. Top Vent - Horizontal Termination - continued1. Top Vent - Horizontal Termination - continued One ElbowTwo Elbows V1 Minimumcontinued 1. Top Vent - Horizontal TerminationThree Elbows H2 V22. Top Vent - Vertical Termination No Elbow V1 = 60 ft. Max. 18.3 m V1 = 3 ft. Min. 914 mmExhaust restrictor Instructions BREAK HERE H 1 Maximum Two ElbowsThree Elbows V 1 + V 2 MinimumOne 45 Elbow 3. Rear Vent - Horizontal Termination No ElbowH1 = 16 in. 406 mm Maximum Heat & Glo ST-36TR-IPI, PIER-36TR-IPI 2176-900 Rev. F 8/11Three Elbows 3. Rear Vent - Horizontal Termination - continuedTwo Elbows V1 H1V1 Minimum 4. Rear Vent - Vertical Termination One ElbowTwo Elbows H1 MaximumThree Elbows 4. Rear Vent - Vertical Termination - continuedThree Elbows H1 MaximumB. Wall Penetration Framing 8 Vent Clearances and FramingA. Pipe Clearances to Combustibles Between ceiling ﬁrestops Between wall shield ﬁrestopsC. Vertical Penetration Framing D. Install Attic Insulation Shield Flat Ceiling InstallationVaulted Ceiling Installation NOTICE Once the vent cap has been removed it CANNOT be reattached 9 Appliance PreparationA. Top Vent Proceed to Section 9. CFigure 9.6 Remove the seal cap B. Rear VentFigure 9.5 Cut the metal retaining band NOTICE Once the vent cap has been removed it CANNOT be reattachedSagging or loose insulation Insulation backing or plastic C. Securing and Leveling the ApplianceWARNING! Risk of Fire! Prevent contact with Framing and other combustible materialsAttach Vent to the Firebox Assembly 10 Installing Vent Pipe DVP and SLP PipeA. Assemble Vent Sections DVP Pipe Only Assemble Pipe Sections DVP Pipe OnlyPilot hole B. Assemble Vent Sections SLP Pipe OnlyC. Assemble Slip Sections Only outer pipes are sealed, sealing the inner ﬂue is not requiredD. Secure the Vent Sections E. Disassemble Vent SectionsCUT HOLE 1/8 in. 3 mm GREATER IN SIZE THAN PATTERN OF SUPPORT F. Install Decorative Ceiling Components SLP onlyLEVEL CATHEDRAL CEILING SUPPORT BOX BOX AS IT IS PROJECTED ONTO ROOF LINECAULK G. Install Metal Roof FlashingH. Assemble and Install Storm Collar CAUTION! Risk of Cuts, Abrasions or Flying DebrisK. Heat Shield Requirements for Horizontal Termination I. Install Vertical Termination CapJ. Install Decorative Wall Components SLP only Heat shields must overlap 1-1/2 in. 38 mm mini- mumL. Install Horizontal Termination Cap DVP and SLP Pipe 1-1/2 38 mm minimum overlap of ﬂue telescoping section is requiredFailure to maintain overlap may cause overheating and ﬁre B. Gas Pressure 11 Gas InformationA. Fuel Conversion C. Gas ConnectionB. IntelliFire Ignition System Wiring A. Wiring RequirementsD. Junction Box Installation C. Electrical Service and RepairE. WSK-MLT Multifunction Wall Switch PrecautionsDetermine Location Wiring the Wall Switch Figure 12.2 Intelliﬁre IPI Wiring DiagramF. Install the Flame Solenoid G. Connect the Temperature Sensor Switch for Fan optionalH. WSK-MLT Operating Instructions I. Setting Flame Height/Manifold PressureJ. Wall Switch Button Operation Temperature ButtonUp and Down Arrows Set Temperature ButtonOperation Under Battery Power Auxiliary Button13 Finishing A. Splatter GuardTo install the Splatter Guard Figure 13.8 Opening Lower Access Panel To Close the Lower Access PanelFigure 13.7 Prepare to Open Lower Access Panel Figure 13.10 Splatter Guard with Lower Access Panel OpenDimensions of Combustibles B. Mantel and Wall ProjectionsDimensions of Combustibles Dimensions of Non-Combustibles1/2 in C. Facing MaterialTOP VIEW FIREPLACEPIER-36TR-IPI D. Finishing MaterialST-36TR-IPI FINISH MATERIAL33-5/8 in Figure 13.22 Pier Door FinishingHeat & Glo ST-36TR-IPI, PIER-36TR-IPI 2176-900 Rev. F 8/11 37-1/4 inE. Elevated Hearth Systems Note 3. Dimensions assume use of a 3/4 in. Hearth PadC. Clean the Appliance 14 Appliance SetupA. Remove Fixed Glass Assembly D. AccessoriesPlacing the Ember Material PILOT ASSEMBLY Log Set Assembly LOGS-MSRF. Install the Log Assembly ASSEMBLY4 3/4 IN 3 2 5 4SHARP NOTCH SHARP NOTCHFLAT AREA 3 2 54 13 4 6 NotchI. Air Shutter Setting G. Fixed Glass AssemblyH. Install Trim Kits and Surrounds Removing Fixed Glass AssemblySymptom 15 TroubleshootingA. IntelliFire Ignition System Possible CausePossible Cause IntelliFire Ignition System - continuedSymptom Corrective ActionLocation A. Appliance Dimension Diagram16 Reference Materials InchesELECTRICAL ACCESSGAS LINE ACCESS G LEFT VIEW C D NDVP-AS2 B. Vent Components DiagramsHeight 24 in./610 mm Heat & GloDVP-TRAP2 B. Vent Components Diagrams continuedDVP-TRAP1 DVP-TRAPK1787 mm B. Vent Components Diagrams continued31 in 13-1/4 in98 mm B. Vent Components Diagrams continued3-7/8 in 10-1/2 inOptional Wire Harness DVP-HRC-SSB. Vent Components Diagrams continued DESCRIPTION45 Elbow B. Vent Components Diagrams continuedSLP45 SLP90 90 ElbowSLP-DCF-BK B. Vent Components Diagrams continuedASSEMBLY SLK-SNKDST-36TR-IPI C. Service PartsLog Set Assembly at DepotC. Service Parts PIER-36TR-IPIStocked Log Set AssemblyPIER-36TR, ST-36TR-IPI #17 Valve AssemblyC. Service Parts at DepotStocked C. Service Parts ListST-36TR-IPI, PIER-36TR-IPI at DepotPlease contact your Heat & Glo dealer with any questions or concerns D. Contact InformationDO NOT DISCARD THIS MANUAL For the location of your nearest Heat & Glo dealer