Appliance Setup, Accessories | Heat & Glo LifeStyle SLR (COSMO)

14 Appliance Setup

A. Remove Fixed Glass Assembly

See Section 14F.

B. Remove the Shipping Materials

Remove shipping materials from inside or underneath the ﬁrebox. The standard black rock media and manual bag assembly are also shipped underneath the ﬁrebox.

C. Clean the Appliance

Clean/vacuum any sawdust that may have accumulated inside the ﬁrebox or underneath in the control cavity.

D. Accessories

Install approved accessories per instructions included with accessories. Install approved accessories per in- structions included with accessories. Contact your dealer for a list of approved accessories.

WARNING! Risk of Fire and Electric Shock! Use ONLY Hearth & Home Technologies-approved optional acces- sories with this appliance. Using non-listed accessories could result in a safety hazard and will void the warranty.

54	Heat & Glo • SLR • 2143-900 Rev. B • 7/08

Image 54

Heat & Glo LifeStyle SLR (COSMO) Appliance Setup, Remove Fixed Glass Assembly, Remove the Shipping Materials, Accessories

Contents

Model SLR Cosmo What to do if you smell gas Congratulations Homeowner Reference Information Table of Contents User Guide Finishing Appliance SetupTroubleshooting Reference Materials Limited Lifetime Warranty Limited Lifetime Warranty Heat & GLO GAS Appliance Products Listing and Code Approvals Installation of Carbon Monoxide Detectors Requirements for the Commonwealth of Massachusetts Gas Fireplace Safety Operating Instructions User GuideYour Fireplace Clear Space Fixed Glass AssemblyRemote Controls, Wall Controls and Wall Switches Decorative Doors and Fronts Lighting Instructions IPI Final inspection by Frequently Asked Questions Initial Break-in ProcedureAfter Fireplace is Lit Glass Cleaning Maintenance and ServiceMaintenance Tasks-Homeowner Remote Control Venting Maintenance Tasks-Qualiﬁed Service TechnicianGasket Seal and Glass Assembly Inspection Firebox Getting Started Typical Appliance System Design and Installation Considerations Tools and Supplies NeededInspect Appliance and Components Framing and Clearances Selecting Appliance Location Constructing the Appliance Chase Clearances Non-combustible Mantels Mantel and Wall ProjectionsCombustible Mantels Front Side Finishing Detail AIR Space Termination Locations Vent Termination Minimum Clearances Covered Alcove Applications Vent Information and Diagrams Top Vent Horizontal Termination Venting with 1 elbow Minimum Maximum Top Vent Horizontal Termination Venting with 2 elbows Top Vent Horizontal Termination Venting with 3 elbows Top Vent Horizontal Termination Venting with 3 elbows Top Vent Vertical Termination No Elbows V1 = 44 ft. Max .4 m Exhaust restrictor Instructions Top Vent Vertical Termination Venting with 2 elbows V1 Minimum Maximum V1 + V2 Minimum Top Vent Vertical Termination Venting with 3 elbows Top Vent Vertical Termination Venting with 4 elbows V1 MIN H1 MAX V2 MIN H2 MAX V3 MIN Wall Penetration Framing Vent Clearances and FramingPipe Clearances to Combustibles Combustible Wall Penetration Install the Ceiling Firestop Pipe SLP Install Attic Insulation Shield Flat Ceiling InstallationVaulted Ceiling Installation Appliance Preparation Top Vent Securing and Leveling the Appliance Proper Positioning, Leveling And Securing Of An Installing Vent Pipe SLP Pipe Assemble Vent Sections Assemble Slip Sections Secure The Vent Sections Install Decorative Ceiling Components Disassemble Vent Sections Install Metal Roof Flashing Assemble and Install Storm Collar Install RF4-8 15 Secure Pipe with SLP-FS Install Vertical Termination Cap Install Decorative Wall ComponentsHeat Shield Requirements for Horizontal Termination Install Horizontal Termination Cap 22 Venting through the wall Gas Information Fuel ConversionGas Pressure Gas Fitting Access Gas Connection Optional Accessories Requirements Wiring RequirementsIntelliﬁre Ignition System Wiring Electrical Information Electrical Service and Repair Junction Box Installation Junction Box Detail Finishing Framing and Finishing Instructions Finishing Details Conﬁrm Fireplace Opening Dimension Opening Facing Material 12 Overlap Fit Method Tonic or Martini Decorative Front 14 Inside Fit Method Tonic Decorative Front Only Decorative Fronts 17 Tonic Decorative Front Clean the Appliance Appliance SetupRemove Fixed Glass Assembly Accessories Cleaning the Rock Rock Media Instructions Screw Install the Mesh Air Shutter SettingAir Shutter Settings Troubleshooting Symptom Possible Cause Corrective ActionIntelliﬁre Ignition System Remove any contaminants that may have accumulated on Appliance Dimension Diagram Reference Materials Vent Components Diagrams DVP-BEK2 Extended Heat Shield SLP-45 45 ElbowSLP90- 90 Elbow RF4-8 Horizontal Ceiling Firestop PVK-80Support Box-Black Adapter Service Parts Part number list on following Service Parts List StockedAt Depot IPI Valve Assembly Contact Information