Heat Controller HEV/H manual General Information

Heat Controller, Inc. HEV/H SERIES Installation, Operation & Maintenance

GENERAL INFORMATION

Inspection

Upon receipt of the equipment, carefully check the shipment against the bill of lading. Make sure all units have been received. Inspect the packaging of each unit, and inspect each unit for damage. Insure that the carrier makes proper notation of any shortages or damage on all copies of the freight bill and completes a common carrier inspection report. Concealed damage not discovered during unloading must be reported to the carrier within 15 days of receipt of shipment. If not filed within 15 days, the freight company can deny the claim without recourse. Note: It is the responsibility of the purchaser to file all necessary claims with the carrier. Notify Heat Controller of all damage within fifteen (15) days of shipment.

Storage

Equipment should be stored in its original packaging in a clean, dry area. Store units in an upright position at all times. Stack units a maximum of 3 units high.

Unit Protection

Cover units on the job site with either the original packaging or an equivalent protective covering. Cap the open ends

of pipes stored on the job site. In areas where painting, plastering, and/or spraying has not been completed, all due precautions must be taken to avoid physical damage to the units and contamination by foreign material. Physical damage and contamination may prevent proper start-up and may result in costly equipment clean-up.

Examine all pipes, fittings, and valves before installing any of the system components. Remove any dirt or debris found in or on these components.

Pre-Installation

IInstallation,Operation,andMaintenanceinstructions areinstructionsprovided arewithprovidedeach unitwith. Horizontaleach unitequipment. Verticalisunit designedconfigurationsfor installationare typicallyaboveinstalledfalse ceilinga mechanicalor in ceiling plenumroom. The. Otherinstallationunit c figurationssite chosenareshouldtypicallyincludeinstalled inadequatemechanical room. The installation site chosen

ervice clearance around the unit. Before should include adequate service clearance around the unit start-up, read all manuals and become familiar

unit. Before unit start-up, read all manuals and become with the unit and its operation. Thoroughly check the familiar with the unit and its operation. Thoroughly check system before operation.

the system before operation.

Prepare units for installation as follows:

1.Compare the electrical data on the unit nameplate with ordering and shipping information to verify that the correct unit has been shipped.

2.Keep the cabinet covered with the original packaging until installation is complete and all plastering, painting, etc. is finished.

3.Verify refrigerant tubing is free of kinks or dents and that it does not touch other unit components.

4.Inspect all electrical connections. Connections must be clean and tight at the terminals.

5.Remove any blower support packaging.

6.Loosen compressor bolts on units equipped with compressor spring vibration isolation until the compressor rides freely on the springs. Remove shipping restraints.

7.REMOVE COMPRESSOR SUPPORT PLATE 1/4” Some airflow patterns are field convertible (horizontal

SHIPPING BOLTS (2 on each side) TO MAXIMIZE units only). Locate the airflow conversion section of

VIBRATION AND SOUND ATTENUATION. this IOM.

8.Some airflow patterns are field convertible (horizontal Locate and verify any hangers, or other accessory

units only). Locate the airflow conversion section of kits located in the compressor section or blower

this IOM. section.

9.Locate and verify any hangers, or other accessory kits located in the compressor section or blower section.

ѥ CAUTION! ѥ

CAUTION! DO NOT store or install units in corrosiveѥenvironmentsCAUTION!or in locationsѥ

subject to temperature or humidity extremes CAUTION! DO NOT store or install units (e.g., attics, garages, rooftops, etc.).

in corrosive environments or in locations Corrosive conditions and high temperature subject to temperature or humidity extremes or humidity can significantly reduce

(e.g., attics, garages, rooftops, etc.). performance, reliability, and service life. Corrosive conditions and high temperature Always move units in an upright position. or humidity can significantly reduce Tilting units on their sides may cause performance, reliability, and service life. equipment damage.

Always move units in an upright position.

Tilting units on their sides may cause

equipment damage.

NOTICE! Failure to remove shipping brackets from spring-mounted compressors will cause

excessive noise, and could cause component NOTICE! Failure to remove shipping brackets failure due to added vibration.

from spring-mounted compressors will cause excessive noise, and could cause component

failure due to added vibration.

ѥ CAUTION! ѥ

CAUTION! CUT HAZARD - Failure to follow this cautionѥmayCAUTION!result in personalѥinjury.

Sheet metal parts may have sharp edges CAUTION! CUT HAZARD - Failure to follow or burrs. Use care and wear appropriate this caution may result in personal injury. protective clothing, safety glasses and Sheet metal parts may have sharp edges gloves when handling parts and servicing

or burrs. Use care and wear appropriate heat pumps.

protective clothing, safety glasses and

gloves when handling parts and servicing heat pumps.

5