HHB comm CDR-882 user manual Playback in DiscSpan Mode, Disc Copy, Advanced Features & Operation

	Advanced Features & Operation
Playback in DiscSpan Mode	When the discs to be used have been loaded, DISC COPY is
	activated by pressing the DISC COPY button (see page 14).
Discs which have been recorded on a CDR-882 in DiscSpan	The display will confirm the “direction” of copy and the total
mode may be replayed on a CDR-882 without any gap in	programme time on the source disc, thus:
programme. The first disc in the sequence may be loaded	Copy CD1-CD2
into either drive, with the second in the other. Note that audio
routing is set automatically to be correct for seamless playback;	Remain 47:52
it is not necessary to make any particular setting of Output Mix
and/or Phones Mix.	or
DISCSPAN mode is automatically set when two DiscSpan-	Copy CD2-CD1
recorded discs are inserted. The PLAY/PAUSE button may
be pressed to start playback from the drive containing the first	Remain 47:52
disc. At the end of the first disc, the IDs that were generated
during recording will be recognised by the operating system and	depending on which drive contains the source disc. The Disc
the second disc will commence playing at the predetermined
	Copy function is also confirmed by a Disc Copy flag at the top of
time as it has been previously been cued up accurately to do so.
	the display. DISC COPY can only be selected when both drives
Its output level will ramp up due to the fade-in that was active
	are in STOP.
during recording, but it will not be heard at this point. During the
subsequent overlap period, however, the monitoring cross-fades	Copying may be started by pressing the ENTER button (the AMS
from the first drive to the second. The audio level from the first
	knob), or aborted by pressing STOP. While copying is under
disc then fades down due to the recording fade-out, and the
	way, the Remain time display counts down to indicate progress.
programme continues from the second drive.
	During copying, STOP may be pressed at any time to abort the
At this point, the first disc may be ejected and removed and	process; a confirmation message will be displayed:
replaced with the third disc (if there is one). At the end of the	Abort Copy?
second disc, the same process is followed, and monitoring
passes back to the first drive, allowing seamless playback of the	Enter-Y Stop-N
sequential programme.
	Pressing ENTER will abort the copy, STOP will cancel and
Disc Copy	copying will continue.
The CDR-882 is equipped with a simple-to-operate DISC COPY	When the disc has been copied, the display confirms this:
function, which enables a copy to be made of a CD at high	Copy
speed. One drive is used for the “source” disc, and a blank CD-
R or CD-RW is inserted in the other. Either drive may be used	Complete
for the “source” disc, recording of the copy taking place in the
other.	The copy is always a completed, finalised disc, regardless of the
The DISC COPY function can only be used if appropriate discs	Auto-Finalize setting in the menu. This applies even if the source
of the correct type are loaded. One drive must contain a CD,	disc was itself unfinalised.
CD-R or CD-RW with programme material; in the case of a CD-	NOTE: DISC COPY is a high-speed copying function which
R or CD-RW, the disc may be unfinalised. The other drive must
contain a completely blank CD-R or CD-RW (partly-recorded,	transfers programme material directly from one drive to the
unfinalised discs will not work). If the CDR-882 detects that	other by using the internal IDE data bus. Thus it is limited to
neither drive contains a blank disc, the following message will be	copying between the drives in a single CDR-882. DISC COPY
displayed:	cannot be used in any Multi-Machine modes, i.e. to make high-
	speed copies between different CDR-882s.
Copy error
No blank CD
or if a non-blank CD-RW is detected, the following message:
Copy Error
Erase CDRW

CDR-882 User Manual Version 1.0 www.hhb.co.uk 41