Definitions, I1max, I1eff | Hobart Welding Products 625 specs

.A complete Parts List is available at www.HobartWelders.com

SECTION 3 − DEFINITIONS

3-1. Symbols And Definitions For Nameplate And Serial Number/Rating Label

Amperes

Plasma Arc Cutting

Adjust Air/Gas

Low Air Pressure

(PAC)

Pressure

Light

Volts

Increase

No − Do Not Do

Temperature

This

Protective Earth

Single Phase

Constant Current

Voltage Input

(Ground)

Off

Percent

Direct Current

Rated No Load

Primary Voltage

Conventional Load

Line Connection

Voltage (Average)

Voltage

I1max

Single Phase

Rated Maximum

Rated Welding

Static Frequency

Supply Current

Current

Duty Cycle

Converter-

Transformer-

Rectifier

Degree Of

Loose Shield Cup

Input

Hertz

Protection

I1eff

Suitable for Some

Power Rating,

Maximum Effective

power factor

Hazardous

Product Of Voltage

Supply Current

Locations

And Current (KVA)

OM-926 Page 9

Page 13

Image 13

Hobart Welding Products 625 manual Definitions, I1max, I1eff

Contents

Processes OM-926Description File Plasma Cutters From Hobart to You Table of Contents Page Marks a special safety message Symbol UsagePlasma Arc Cutting Hazards Cutting can cause fire or explosion Flying Sparks can cause injury Exploding Parts can injureARC Rays can burn eyes and skin Noise can damage hearing California Proposition 65 Warnings EMF Information Principal Safety StandardsAbout Pacemakers LE Coupage présente un risque de feu ou d’explosion Signification des symbolesUNE Décharge Électrique peut entraîner la mort Identifie un message de sécurité particulier LE Bruit peut endommager l’ouïe Risque de blessure en casLES Fumées ET LES GAZ peuvent être dangereux LE Plasma D’ARC peut entraîner des blessures DES Organes Mobiles peuvent provoquer des blessures DES Pieces Chaudes peuvent pro- voquer des brûlures gravesLA Chute DE L’APPAREIL peut blesser Risque D’INCENDIE OU Information sur les champs électromagnétiques Principales normes de sécuritéLE Coupage Ã L’ARC peut causer des interférence Consignes relatives aux stimulateurs cardiaques I1max − DefinitionsI1eff Specifications − InstallationSpecifications For Torch Torch Dimensions And Weight Dimensions And Weight Unit Dimensions, Weight, And MovementMovement Do not move or operate unit where it could tip 90-120 psi Connecting Work Clamp and Gas/Air SupplyRear of Unit 50/60 Hz Single Phase Electrical Service GuideTime-Delay Extension Cord Data Do not move or operate unit where it could tip = GND/PE Selecting a Location And Connecting Input Power Always connect green or Prong Not UsedTerminal, never to a load Terminals Setting Gas/Air Pressure Installing Alternative PlugSetting Gas/Air Pressure − Operation Pressure Gauge Pressure Adjustment KnobControls Cutting Speed Pilot arc starts immediately when trigger is pressed Trigger Safety LockWhen doing extended non-shielded Plasma Cutting System Practices Area as possible Sequence Of Cutting Operation Hold torch at approximately Angle to workpiece Sequence Of Gouging Operation Cutting Sequence Of Piercing Operation Routine Maintenance − Maintenance & Troubleshooting Shield Cup Checking Torch Shield Cup Shutdown System Checking/Replacing Retaining Cup, Tip, And Electrode Turn Off power source before checking torch parts Check torch consumables Troubleshooting Power SourceIs Temp Status Light On? Is Pressure Status Troubleshooting Torch Circuit Diagram − Electrical Diagram Recommended Spare Parts − Parts ListRecommended Spare Parts 195 110 ICE-40C 25ft Torch 195 111 ICE-40C 50ft Torch See -1for additional Consumable parts Work like a Pro Support ServiceAssistance Hobart Welding Products Contact your Distributor for