See -1for additional Consumable parts | Hobart Welding Products 625

NOTE: The ICE-40C torch is specifically for use only with this plasma cutting unit.

See Figure 8-1for additional

consumable parts.

Item Part

No. No. Description

195 110 ICE-40C 25ft Torch

195 111 ICE-40C 50ft Torch

1183 427 Handle Assy, complete (1)

2192 059 Main Body (1)

3209 298 Leads, 25ft (1)

3209 299 Leads, 50ft (1)

4185 833 Switch Assembly w/spring (1)

5171 248 Push Button Switch (1)

6190 220 Spring, trigger assembly

169 231 Grease, silicone (1)

Ref. 195 092 / Ref. 803 224

Figure 8-2. Torch, ICE-40C

NOTE

Acomplete Parts List is available on-line at www.HobartWelders.com

To maintain the factory original performance of your equipment, use only Manufacturer’s Suggested Replacement Parts. Model and serial number required when ordering parts from your local distributor.

OM-926 Page 29

Page 33

Image 33

Hobart Welding Products 625 See -1for additional Consumable parts, 195 110 ICE-40C 25ft Torch 195 111 ICE-40C 50ft Torch

Contents

Processes OM-926Description File Plasma Cutters From Hobart to You Table of Contents Page Marks a special safety message Symbol UsagePlasma Arc Cutting Hazards Cutting can cause fire or explosion Flying Sparks can cause injury Exploding Parts can injureARC Rays can burn eyes and skin Noise can damage hearing California Proposition 65 Warnings Principal Safety Standards EMF InformationAbout Pacemakers LE Coupage présente un risque de feu ou d’explosion Signification des symbolesUNE Décharge Électrique peut entraîner la mort Identifie un message de sécurité particulier LE Bruit peut endommager l’ouïe Risque de blessure en casLES Fumées ET LES GAZ peuvent être dangereux LE Plasma D’ARC peut entraîner des blessures DES Organes Mobiles peuvent provoquer des blessures DES Pieces Chaudes peuvent pro- voquer des brûlures gravesLA Chute DE L’APPAREIL peut blesser Risque D’INCENDIE OU Information sur les champs électromagnétiques Principales normes de sécuritéLE Coupage Ã L’ARC peut causer des interférence Consignes relatives aux stimulateurs cardiaques − Definitions I1maxI1eff Specifications − InstallationSpecifications For Torch Torch Dimensions And Weight Unit Dimensions, Weight, And Movement Dimensions And WeightMovement Do not move or operate unit where it could tip Connecting Work Clamp and Gas/Air Supply 90-120 psiRear of Unit 50/60 Hz Single Phase Electrical Service GuideTime-Delay Extension Cord Data Do not move or operate unit where it could tip = GND/PE Selecting a Location And Connecting Input Power Always connect green or Prong Not UsedTerminal, never to a load Terminals Installing Alternative Plug Setting Gas/Air PressureSetting Gas/Air Pressure − Operation Pressure Gauge Pressure Adjustment KnobControls Cutting Speed Pilot arc starts immediately when trigger is pressed Trigger Safety LockWhen doing extended non-shielded Plasma Cutting System Practices Area as possible Sequence Of Cutting Operation Hold torch at approximately Angle to workpiece Sequence Of Gouging Operation Cutting Sequence Of Piercing Operation Routine Maintenance − Maintenance & Troubleshooting Shield Cup Checking Torch Shield Cup Shutdown System Checking/Replacing Retaining Cup, Tip, And Electrode Turn Off power source before checking torch parts Check torch consumables Troubleshooting Power SourceIs Temp Status Light On? Is Pressure Status Troubleshooting Torch Circuit Diagram − Electrical Diagram − Parts List Recommended Spare PartsRecommended Spare Parts 195 110 ICE-40C 25ft Torch 195 111 ICE-40C 50ft Torch See -1for additional Consumable parts Work like a Pro Service SupportAssistance Hobart Welding Products Contact your Distributor for

Hobart Welding Products 625 manual See -1for additional Consumable parts

Models: 625

See Figure 8-1for additional

consumable parts.

Item Part

No. No. Description

195 110 ICE-40C 25ft Torch

195 111 ICE-40C 50ft Torch

Figure 8-2. Torch, ICE-40C

To maintain the factory original performance of your equipment, use only Manufacturer’s Suggested Replacement Parts. Model and serial number required when ordering parts from your local distributor.