Hobart Welding Products OM-198 683C manual Wire Drive And Gears -2 Item

Item		Dia.	Part	Description
	No.	Mkgs.	No.		Quantity
				Figure 6-5. Wire Drive And Gears (Fig 6-2 Item 26)
. . .	1 . . .	. . . . . . .	. 602 009 . . .	SCREW, .250-20 x 1.25 soc hd gr 8	. . . 1
. . .	2 . . .	. . . . . . .	. 172 075 . . .	CARRIER, drive roll w/components	. . . 1
. . .	3 . . .	. . . . . . .	. 166 072 . . .	SPACER, gear	. . . 1
. . .	4 . . .	. . . . . . .	. 010 224 . . .	PIN, spring CS .187 x 1.000	. . . 1
. . .	5 . . .	. . . . . . .	. 182 788 . . .	HOUSING, adapter gun/feeder	. . . 1
. . .	6 . . .	. . . . . . .	. 085 242 . . .	FASTENER, pinned	. . . 1
. . .	7 . . .	. . . . . . .	. 196 896 . . .	CUP, spring	. . . 1
. . .	8 . . .	. . . . . . .	. 196 897 . . .	SPRING, cprsn .695 OD x .095 wire	. . . 1
. . .	9 . . .	. . . . . . .	. 196 895 . . .	KNOB, tension adj	. . . 1
. . . 10 . . .		. . . . . . .	. 166 071 . . .	LEVER, mtg pressure gear	. . . 1
. . . 11 . . .		. . . . . . .	. 079 634 . . .	PIN, hinge	. . . 1
. . . 12 . . .		. . . . . . .	. 151 828 . . .	PIN, cotter hair .054 x .750	. . . 2
. . . 13 . . .		. . . . . . .	. 173 616 . . .	COVER, right angle motor	. . . 1
. . . 14 . . .		PM . . . 173 435 . . .		MOTOR, gear 24VDC 122RPM 20:1 ratio (consisting of)	. . . 1
. . .	. . . . . .	. . . . . . .	. 193 633 . . .	. KEY, woodruff .118 x .380	. . . 1
. . .	. . . . . .	. . . . . . .	. 193 634 . . .	. WASHER, wave .405 ID x .740 OD	. . . 2
. . .	. . . . . .	. . . . . . .	. 193 635 . . .	. RING, rtng ext .394 shaft x	. . . 1
. . . 15 . . .		. . . . . . .	. 079 633 . . .	FITTING, hose brs barbed M 3/16tbg	. . . 1
. . . 16 . . .		. . . . . . .	. 601 966 . . .	SCREW, .375–16 x 1.25hexhd	. . . 2
. . . 18 . . .		. . . . . . .	. 604 538 . . .	WASHER, flat stl SAE .312	. . . 1
. . . 19 . . .		. . . . . . .	. 124 778 . . .	KNOB, plstc T 1.000 lg x .312-18 x 2.000 bar	. . . 1
. . . 20 . . .		. . . . . . .	. 173 619 . . .	CARRIER, drive roll w/components	. . . 1
. . . 21 . . .		. . . . . . .	. 174 609 . . .	SCREW, M 4–.7 x 12	. . . 1
. . . 22 . . .		. . . . . . .	. 174 610 . . .	SCREW, M 6–1.0 x 20 soc hd	. . . 3
. . . 23 . . .		. . . . . . .	. 192 029 . . .	WASHER, flat .250 ID x .437 OD	. . . 3
. . . 24 . . .		. . . . . . .	. 173 620 . . .	BUSHING, motor mtg	. . . 3
. . . 25 . . .		. . . . . . .	. 602 243 . . .	WASHER, flat .438 ID X 1.00 OD	. . . 1
. . . 26 . . .		. . . . . . .	. 602 213 . . .	WASHER, lock .380 ID X .683 OD	. . . 1
. . .	. . . . . .	. . . . . . .	*045 233 . . .	GUIDE, anti-wear	. . . 1

See Table 6-1

Drive Roll & Wire Guide Kits.

.Hardware is common and not available unless listed.

Figure 6-5. Wire Drive And Gears

148 529-H

*Recommended Spare Parts.

To maintain the factory original performance of your equipment, use only Manufacturer’s Suggested Replacement Parts. Model and serial number required when ordering parts from your local distributor.

OM-198 683 Page 35