Hobart Welding Products OM-198 683C manual Drive Roll And Wire Guide Kits

Table 6-1. Drive Roll And Wire Guide Kits

Note Base selection of drive rolls upon the following recommended usages:

1V-Grooved rolls for hard wire.

2U-Grooved rolls for soft and soft shelled cored wires.

3U-Cogged rolls for extremely soft shelled wires (usually hard surfacing types).

4V-Knurled rolls for hard shelled cored wires.

5Drive roll types may be mixed to suit particular requirements (example: V-Knurled roll in combination with U-Grooved).

				Wire Diameter				Kit No.		Drive Roll		Inlet
			Fraction			Decimal	Metric			Part No.	Type	Wire Guide
			.023/.025 in.		.023/.025 in.		0.6 mm	087 131		087 130	V-Grooved	056 192
			.030 in.			.030 in.	0.8 mm	079 594		053 695	V-Grooved	056 192
			.035 in.			.035 in.	0.9 mm	079 595		053 700	V-Grooved	056 192
			.045 in.			.045 in.	1.2 mm	079 596		053 697	V-Grooved	056 193
			.052 in.			.052	1.3 mm	079 597		053 698	V-Grooved	056 193
			1/16 in.			.062	1.6 mm	079 598		053 699	V-Grooved	056 195
												Ref. S-0026-B/7-91
Item			Dia.	Part
	No.	Mkgs.		No.				Description				Quantity
						Figure 6-6. Panel, Rear w/Components (Fig 6-1 Item 3)
. . .	1 . . .	.	. . . . . . .	148 809		. . . BLADE, fan 9 in 5wg 34deg .309 bore CCW .					. . . . . . . . . . . . .	. . . . . . . . . . . . . 1
. . . 2 . . . FM1 . . .				188 706		. . . MOTOR, fan 230V 50/60 Hz 1550RPM .312dia shaft						. . . . . . . . . . . . . 1
. . . 3 . . .		.	. . . . . . .	188 709		. . . WINDTUNNEL, 9 in				. . . . . . . . . .	. . . . . . . . . . . . .	. . . . . . . . . . . . . 1
. . . 4 . . . GS1 . . .				125 785		. . . VALVE, 24VAC 2 way custom port 1/8 orf . . .					. . . . . . . . . . . . .	. . . . . . . . . . . . . 1
. . .	5 . . .	.	. . . . . . .	143 810		. . . +PANEL, rear . . .		. . . . . . . . . . . .	. . .	. . . . . . . . . .	. . . . . . . . . . . . .	. . . . . . . . . . . . . 1
. . .	6 . . .	.	. . . . . . .	169 654		. . . BRACKET, support tank				. . . . . . . . . .	. . . . . . . . . . . . .	. . . . . . . . . . . . . 1
. . .	7 . . .	.	. . . . . . .	188 441		. . . CHAIN, weldless 2/0 x 31.000 lg .				. . . . . . . . . .	. . . . . . . . . . . . .	. . . . . . . . . . . . . 1
. . .	8 . . .	.	. . . . . . .	605 227		. . . NUT, nyl hex jam .750NPST				. . . . . . . . . .	. . . . . . . . . . . . .	. . . . . . . . . . . . . 1
. . .	9 . . .	.	. . . . . . .	178 126		. . . CONNECTOR, clamp cable .690/1.070					. . . . . . . . . . . . .	. . . . . . . . . . . . . 1
. . .	. . . . . .	.	. . . . . . .	193 328		. . . LABEL, warning .		. . . . . . . . . . . .	. . .	. . . . . . . . . .	. . . . . . . . . . . . .	. . . . . . . . . . . . . 1

. Hardware is common and	6
not available unless listed.
5	7

4

8

9

3

2

1

Ref. 802 088-A

Figure 6-6. Panel, Rear w/Components

+When ordering a component originally displaying a precautionary label, the label should also be ordered.

To maintain the factory original performance of your equipment, use only Manufacturer’s Suggested Replacement Parts. Model and serial number required when ordering parts from your local distributor.

OM–198 683 Page 36