5-3. Weld Parameter Chart For 230 VAC Model
Welding Guide for 230 Volt
|
|
|
|
|
|
|
|
| Settings are approximate. Adjust as required. Thicker materials can be welded |
|
|
| |||
| using proper technique, joint preparation and multiple passes. |
|
|
|
| ||
| Material | Wire Type | Suggested | Diameter | 24 ga. | 20 ga. |
|
| Being | and | Shielding Gas | of Wire |
| ||
| Welded | Polarity Setting | 20−30 CFH Flow Rate | Being Used | .024 in. | .036 in. |
|
|
|
|
|
| (0.6 mm) | (0.8 mm) |
|
|
| Flux Cored | No shielding gas required | .030” (0.8 mm) | ~ | ~ |
|
| Steel | E71T−11 | Good for windy or |
|
|
|
|
| (DCEN) | outdoor applications. | .035” (0.9 mm) | ~ | ~ |
| |
|
|
|
|
|
|
|
|
|
|
|
| .045” (1.2 mm) | ~ | ~ |
|
|
| Solid Wire | C25 Gas Mixture |
|
|
|
|
|
| .024” (0.6 mm) | 1 / 30 | 1 / 35 |
| ||
| Steel | ER70S−6 | 75% Argon / 25% CO2 |
|
|
|
|
|
|
|
|
| |||
| (DCEP) | Produces less spatter. | .030” (0.8 mm) | ~ | 1 / 30 |
| |
|
|
| |||||
|
|
| Better appearance. |
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
| .035” (0.9 mm) | ~ | ~ |
|
|
| Solid Wire |
|
|
|
|
|
|
|
| .024” (0.6 mm) | ~ | ~ |
| |
| Steel | ER70S−6 | 100% CO2 |
|
|
|
|
| (DCEP) | .030” (0.8 mm) | ~ | ~ |
| ||
|
|
|
| ||||
|
|
|
|
|
|
|
|
|
|
|
| .035” (0.9 mm) | ~ | ~ |
|
|
|
|
|
|
|
|
|
| Stainless | Stainless |
| .024” (0.6 mm) | ~ | ~ |
|
| Tri−Mix |
|
|
|
| ||
| Steel | Steel | 90% He / 7.5% Ar / 2.5% CO2 | .030” (0.8 mm) | ~ | ~ |
|
|
| (DCEP) |
|
|
|
|
|
|
|
|
| .035” (0.9 mm) | ~ | ~ |
|
|
| Aluminum** |
|
|
|
|
|
| Aluminum | 100% Argon** | .030” (0.8 mm) | ~ | ~ |
| |
| (DCEP) |
|
|
|
| ||
|
|
|
|
| |||
|
|
|
|
|
|
| |
|
|
|
| .035” (0.9 mm) | ~ | ~ |
|
Match feedroll groove to diameter of wire being used. Set Tension Knob Setting to 3 at start.
Adjust tension per instructions in the manual.
CAUTION! Do not change Voltage switch position while welding. See owners manual for more information.
*Multiple passes required. **Aluminum wire is soft so feedability is not as good.
Return To Table Of Contents |
