Honda Europe Power Equipment S.A
TONDEUSE AUTOPORTEE LAWN-TRACTOR RASENTRAKTOR
TRATTORINO RASAERBA ZITMAAIER
HF2315SBE HF2315HME HF2415SBE HF2417HME HF2417HTE HF2620HME HF2620HTE
AFTER-SALES SERVICE
INTRODUCTION
TABLE OF CONTENTS
1. SAFETY REGULATIONS
1.1 HOW TO READ THE MANUAL
or others
death to oneself or others
1.2 SAFETY REGULATIONS read carefully before using the machine
fumes can collect 2 Mow only in daylight or good artificial light
1.3 SAFETY DECALS
1.4 REGULATIONS FOR TOWING
3 = Danger! Ejected objects
4 = Danger! Ejected objects
HOW TO RECOGNIZE YOUR MACHINE
2. IDENTIFICATION OF THE MACHINE AND COMPONENTS
2.1 IDENTIFICATION OF THE MACHINE
tive 2000/14/EEC
2.2 IDENTIFICATION OF MAIN COMPONENTS
3.1 UNPACKING
3. UNPACKING AND ASSEMBLY
3.2 FITTING THE STEERING WHEEL
3.4 FRONT BUMPER ASSEMBLY if fitted
3.5 CONNECTING THE BATTERY
same size to push the pin in the last part
3.3 FITTING THE SEAT
To prevent the safety device in the electronics card from cut
ting in, never start the engine until the battery is fully charged
Battery acid is corrosive and a pollutant. When handling
uting it evenly among the six elements
3.7 ASSEMBLING THE LEVERS FOR TIPPING THE GRASS-CATCHER
3.9 GRASS-CATCHER ASSEMBLY
3.8 REMOVAL OF THE STOP FROM THE HOOKING PAWL OF THE GRASS- CATCHER
Page
4. CONTROLS AND INSTRUMENTS
spond to
HF2SBE
HF2315HME HF2417
HF2620
4.7 PUSH-BUTTON FOR REVERSE MOWING
a The display comes on when the key is inserted
Afterwards, when a warning light comes on, it indicates
pedal
When the machine is in movement, keep your foot off the
stopped
stopped
4.5 is engaged, the engine stops
N F N
5. HOW TO USE
5.1 SAFETY RECOMMENDATIONS
Do not tamper with or remove the safety devices fitted to the machine
5.2 WHY THE SAFETY DEVICES CUT IN
To start the engine, in all cases it is necessary that
5.3 PRELIMINARY OPERATIONS BEFORE STARTING WORK
Use oil SAE 10W30 and Petrol Unleaded Euro
Running the engine with an
insufficient amount of oil can damage it very seri
ously. The use of a non-detergent or two-stroke
The protection devices must be fitted with
5.4 USING THE MACHINE
engine starting when the blades are engaged
the transmission is not in neutral «N»
the operator is absent with the parking brake disengaged
areas closed to traffic
roads. It has to be used as indicated by the Highway Code in private
and the cutting deck put at its highest position position «7»
releasing the drive pedal in forward or reverse
Reverse must be engaged ONLY when the machine is stopped
all four wheels, WITH THE ENGINE OFF AND
THE BLADES DISENGAGED
High and dense grass - wet lawn
2,5 km/h
The dumping switch operates
switch. To stop the signal, disengage the blades
Emptying the grass-catcher
can only be done with the blades disengaged
WARNING! This job must only be performed with the engine turned off
unattended
Never use hose-nozzles or harsh detergents for cleaning the
do not clean the clutch with petrol
body and engine
For washing the inside of the cutting deck
next time the machine is used
Empty the fuel tank by disconnect
ing the tube situated at the inlet of
the fuel filter
do not reverse the leads on the battery terminals
5.5 USING ON SLOPING GROUND
be careful not to cause short-circuits
REDUCE SPEED BEFORE ANY CHANGE OF DIRECTION
5.7 ADVICE ON HOW TO OBTAIN A GOOD CUT
5.6 TRANSPORTING
directions
Start the engine Go forward Brake or stop Reverse
Move the accelerator
HF2HME HF2HTE press the drive pedal forward
the engine remove the grass-catcher and clean the channel
HF2SBE
HF2HME
HF2HTE
6. MAINTENANCE
6.1 SAFETY RECOMMENDATIONS
Summary of the main situations where work may be required
6.2 ROUTINE MAINTENANCE
a Periodic maintenance
HOURS
HOURS
HF2315
b Lubrication
HF2315
HF2S
HF24
Blade replacement
tery on your machine must be charged before using for the first time
No device other than the battery charger is to be connected
to this connector
The charge must be maintained with the battery charger, fol
a Removing the cutting deck
6.3 CHECKS AND ADJUSTMENTS
Having checked that there is nothing in
Put the cutting height adjustment lever into the notch at position
gloves when handling the blades
b Dismantling, sharpening and balancing blades
Wear heavy
To remove a blade, hold it firmly and
When installing them, make sure that they are correctly
When re-fitting
ing screws 2 using a torque
put the height adjusting lever into
7 - 9 of the three trace rods until the deck is resting on the blocks
Turn the adjusting nut 1 until the correct
spring length 2 is achieved measured
6.3.4 BRAKE ADJUSTMENT
measured inside the washers. When the adjust
work properly even after this adjustment
great care when using for the first few times as
B = 45 - 47 mm
6.4 DISMANTLING AND REPLACEMENT
WARNING! Never use gasoline or low flash point solvents for cleaning
the air cleaner element. A fire or explosion could result
wrench special tool
6. Tighten the oil filter to the specified torque 12 Nm - 1.20 kgm
cleaner cover 2, and remove the cover
air cleaner case when servicing the air cleaner
5. Reinstall the air cleaner elements and the cover
When installing a new spark plug, tighten 1/2 turn after the
tightened spark plugs can become very hot and may damage the engine
prevent an uneven cut
carefully re-fit the snap ring 1 and washer
The wheels are held by a snap ring 1 which
type and rating, and never with one of another rating
wear! ALWAYS USE GENUINE REPLACEMENT BELTS
1 - 10 Amps - Red
7. TROUBLESHOOTING
PROBLEM
SOLUTION
LIKELY CAUSE
HF2220
models with
lever operated
engagement
WARNING! Do not take on complicated repair work if you dont
have the necessary equipment and the technical knowledge
models with
electromagnetic
8. ACCESSORIES OPTIONAL
1. STONE-GUARD KIT
2. TOWING HITCH
3. MULCHING PLUG
9. SPECIFICATIONS
HF2315SBE
HF2315HME
HF2415SBE
10. ALPHABETICAL INDEX
ALPHABETICAL INDEX