Manuals / Honda Power Equipment / Lawn and Garden / Lawn Mower

Honda Power Equipment HF2620HME, HF2417HTE, HF2415SBE Turn the adjusting nut 1 until the correct

Models: HF2315SBE HF2417HME HF2315HME HF2620HTE HF2415SBE HF2620HME HF2417HTE

1 65

Download 65 pages 48.37 Kb

Page 50

Turn the adjusting nut (1) until the correct

MAINTENANCE

EN 49

	– turn both the rear screws (5) until the rear
	of the deck begins to rise both at the right	4	3	7
	and the left, and then tighten the relative	4	3	7
	and the left, and then tighten the relative
	locknuts (6).

If you are unable to adjust the cutting deck properly, contact your Dealer.

6.3.3ADJUSTING BLADE ENGAGEMENT AND BLADE BRAKE

When the lever to disengage the blades is operated, this also brings the blade brake into operation for stopping the blades within few seconds.

A stretched cable and changes in the length of the belt can impair the blades’ engagement or rotation.

In this case, you have to work on the adjuster according to the different methods provided for each model.

In any event, if the engagement is unable to normally drive the belt or the blades do not stop within a few seconds after adjustment, immediately contact your Deal- er.

	➤ HF2315SBE	2
	➤ HF2315SBE	1
		1

Turn the adjusting nut (1) until the correct spring length (2) is achieved (measured with the blade engaged).

88 ⎟ 90 mm

1

➤

HF2415SBE

2

Turn the adjusting nut (1) until the correct	94 ⎟ 96 mm
spring length (2) is achieved (measured

with the blades engaged).

Image 50

Honda Power Equipment HF2620HME Turn the adjusting nut 1 until the correct, spring length 2 is achieved measured

Contents

TRATTORINO RASAERBA ZITMAAIER Honda Europe Power Equipment S.ATONDEUSE AUTOPORTEE LAWN-TRACTOR RASENTRAKTOR HF2315SBE HF2315HME HF2415SBE HF2417HME HF2417HTE HF2620HME HF2620HTEAFTER-SALES SERVICE INTRODUCTIONTABLE OF CONTENTS or others 1. SAFETY REGULATIONS1.1 HOW TO READ THE MANUAL death to oneself or others1.2 SAFETY REGULATIONS read carefully before using the machine fumes can collect 2 Mow only in daylight or good artificial light 3 = Danger! Ejected objects 1.3 SAFETY DECALS1.4 REGULATIONS FOR TOWING 4 = Danger! Ejected objects2.1 IDENTIFICATION OF THE MACHINE HOW TO RECOGNIZE YOUR MACHINE2. IDENTIFICATION OF THE MACHINE AND COMPONENTS tive 2000/14/EEC2.2 IDENTIFICATION OF MAIN COMPONENTS 3.2 FITTING THE STEERING WHEEL 3. UNPACKING AND ASSEMBLY3.1 UNPACKING same size to push the pin in the last part 3.4 FRONT BUMPER ASSEMBLY if fitted3.5 CONNECTING THE BATTERY 3.3 FITTING THE SEATBattery acid is corrosive and a pollutant. When handling To prevent the safety device in the electronics card from cutting in, never start the engine until the battery is fully charged uting it evenly among the six elements3.7 ASSEMBLING THE LEVERS FOR TIPPING THE GRASS-CATCHER 3.9 GRASS-CATCHER ASSEMBLY 3.8 REMOVAL OF THE STOP FROM THE HOOKING PAWL OF THE GRASS- CATCHERPage 4. CONTROLS AND INSTRUMENTS spond to HF2620 HF2SBEHF2315HME HF2417 4.7 PUSH-BUTTON FOR REVERSE MOWINGa The display comes on when the key is inserted Afterwards, when a warning light comes on, it indicates stopped When the machine is in movement, keep your foot off thepedal N F N 4.5 is engaged, the engine stopsstopped Do not tamper with or remove the safety devices fitted to the machine 5. HOW TO USE5.1 SAFETY RECOMMENDATIONS 5.2 WHY THE SAFETY DEVICES CUT INTo start the engine, in all cases it is necessary that 5.3 PRELIMINARY OPERATIONS BEFORE STARTING WORK insufficient amount of oil can damage it very seri Use oil SAE 10W30 and Petrol Unleaded EuroRunning the engine with an ously. The use of a non-detergent or two-strokeThe protection devices must be fitted with the transmission is not in neutral «N» 5.4 USING THE MACHINEengine starting when the blades are engaged the operator is absent with the parking brake disengagedand the cutting deck put at its highest position position «7» roads. It has to be used as indicated by the Highway Code in privateareas closed to traffic releasing the drive pedal in forward or reverse Reverse must be engaged ONLY when the machine is stoppedHigh and dense grass - wet lawn all four wheels, WITH THE ENGINE OFF ANDTHE BLADES DISENGAGED 2,5 km/hEmptying the grass-catcher The dumping switch operatesswitch. To stop the signal, disengage the blades can only be done with the blades disengagedWARNING! This job must only be performed with the engine turned off unattendedbody and engine Never use hose-nozzles or harsh detergents for cleaning thedo not clean the clutch with petrol For washing the inside of the cutting decking the tube situated at the inlet of next time the machine is usedEmpty the fuel tank by disconnect the fuel filterbe careful not to cause short-circuits do not reverse the leads on the battery terminals5.5 USING ON SLOPING GROUND REDUCE SPEED BEFORE ANY CHANGE OF DIRECTION5.7 ADVICE ON HOW TO OBTAIN A GOOD CUT 5.6 TRANSPORTINGMove the accelerator directionsStart the engine Go forward Brake or stop Reverse HF2HME HF2HTE press the drive pedal forwardHF2HME the engine remove the grass-catcher and clean the channelHF2SBE HF2HTESummary of the main situations where work may be required 6. MAINTENANCE6.1 SAFETY RECOMMENDATIONS 6.2 ROUTINE MAINTENANCEHOURS a Periodic maintenanceHOURS HF2315HF2S b LubricationHF2315 HF24Blade replacement to this connector tery on your machine must be charged before using for the first timeNo device other than the battery charger is to be connected The charge must be maintained with the battery charger, folHaving checked that there is nothing in 6.3 CHECKS AND ADJUSTMENTSa Removing the cutting deck Put the cutting height adjustment lever into the notch at position Wear heavy gloves when handling the bladesb Dismantling, sharpening and balancing blades To remove a blade, hold it firmly anding screws 2 using a torque When installing them, make sure that they are correctlyWhen re-fitting put the height adjusting lever into7 - 9 of the three trace rods until the deck is resting on the blocks Turn the adjusting nut 1 until the correct spring length 2 is achieved measured6.3.4 BRAKE ADJUSTMENT great care when using for the first few times as measured inside the washers. When the adjustwork properly even after this adjustment B = 45 - 47 mm6.4 DISMANTLING AND REPLACEMENT wrench special tool WARNING! Never use gasoline or low flash point solvents for cleaningthe air cleaner element. A fire or explosion could result 6. Tighten the oil filter to the specified torque 12 Nm - 1.20 kgmcleaner cover 2, and remove the cover air cleaner case when servicing the air cleaner 5. Reinstall the air cleaner elements and the coverWhen installing a new spark plug, tighten 1/2 turn after the carefully re-fit the snap ring 1 and washer tightened spark plugs can become very hot and may damage the engineprevent an uneven cut The wheels are held by a snap ring 1 which1 - 10 Amps - Red wear! ALWAYS USE GENUINE REPLACEMENT BELTStype and rating, and never with one of another rating SOLUTION 7. TROUBLESHOOTINGPROBLEM LIKELY CAUSElever operated HF2220models with engagementmodels with WARNING! Do not take on complicated repair work if you donthave the necessary equipment and the technical knowledge electromagnetic2. TOWING HITCH 8. ACCESSORIES OPTIONAL1. STONE-GUARD KIT 3. MULCHING PLUGHF2315HME 9. SPECIFICATIONSHF2315SBE HF2415SBE10. ALPHABETICAL INDEX ALPHABETICAL INDEX