TONDEUSE AUTOPORTEE LAWN-TRACTOR RASENTRAKTOR
Honda Europe Power Equipment S.A
TRATTORINO RASAERBA ZITMAAIER
HF2315SBE HF2315HME HF2415SBE HF2417HME HF2417HTE HF2620HME HF2620HTE
INTRODUCTION
AFTER-SALES SERVICE
TABLE OF CONTENTS
1.1 HOW TO READ THE MANUAL
1. SAFETY REGULATIONS
or others
death to oneself or others
1.2 SAFETY REGULATIONS read carefully before using the machine
fumes can collect 2 Mow only in daylight or good artificial light
1.4 REGULATIONS FOR TOWING
1.3 SAFETY DECALS
3 = Danger! Ejected objects
4 = Danger! Ejected objects
2. IDENTIFICATION OF THE MACHINE AND COMPONENTS
HOW TO RECOGNIZE YOUR MACHINE
2.1 IDENTIFICATION OF THE MACHINE
tive 2000/14/EEC
2.2 IDENTIFICATION OF MAIN COMPONENTS
3.2 FITTING THE STEERING WHEEL
3. UNPACKING AND ASSEMBLY
3.1 UNPACKING
3.5 CONNECTING THE BATTERY
3.4 FRONT BUMPER ASSEMBLY if fitted
same size to push the pin in the last part
3.3 FITTING THE SEAT
ting in, never start the engine until the battery is fully charged
To prevent the safety device in the electronics card from cut
Battery acid is corrosive and a pollutant. When handling
uting it evenly among the six elements
3.7 ASSEMBLING THE LEVERS FOR TIPPING THE GRASS-CATCHER
3.8 REMOVAL OF THE STOP FROM THE HOOKING PAWL OF THE GRASS- CATCHER
3.9 GRASS-CATCHER ASSEMBLY
Page
4. CONTROLS AND INSTRUMENTS
spond to
HF2315HME HF2417
HF2SBE
HF2620
4.7 PUSH-BUTTON FOR REVERSE MOWING
a The display comes on when the key is inserted
Afterwards, when a warning light comes on, it indicates
stopped
When the machine is in movement, keep your foot off the
pedal
N F N
4.5 is engaged, the engine stops
stopped
5.1 SAFETY RECOMMENDATIONS
5. HOW TO USE
Do not tamper with or remove the safety devices fitted to the machine
5.2 WHY THE SAFETY DEVICES CUT IN
To start the engine, in all cases it is necessary that
5.3 PRELIMINARY OPERATIONS BEFORE STARTING WORK
Running the engine with an
Use oil SAE 10W30 and Petrol Unleaded Euro
insufficient amount of oil can damage it very seri
ously. The use of a non-detergent or two-stroke
The protection devices must be fitted with
engine starting when the blades are engaged
5.4 USING THE MACHINE
the transmission is not in neutral «N»
the operator is absent with the parking brake disengaged
and the cutting deck put at its highest position position «7»
roads. It has to be used as indicated by the Highway Code in private
areas closed to traffic
Reverse must be engaged ONLY when the machine is stopped
releasing the drive pedal in forward or reverse
THE BLADES DISENGAGED
all four wheels, WITH THE ENGINE OFF AND
High and dense grass - wet lawn
2,5 km/h
switch. To stop the signal, disengage the blades
The dumping switch operates
Emptying the grass-catcher
can only be done with the blades disengaged
unattended
WARNING! This job must only be performed with the engine turned off
do not clean the clutch with petrol
Never use hose-nozzles or harsh detergents for cleaning the
body and engine
For washing the inside of the cutting deck
Empty the fuel tank by disconnect
next time the machine is used
ing the tube situated at the inlet of
the fuel filter
5.5 USING ON SLOPING GROUND
do not reverse the leads on the battery terminals
be careful not to cause short-circuits
REDUCE SPEED BEFORE ANY CHANGE OF DIRECTION
5.6 TRANSPORTING
5.7 ADVICE ON HOW TO OBTAIN A GOOD CUT
Start the engine Go forward Brake or stop Reverse
directions
Move the accelerator
HF2HME HF2HTE press the drive pedal forward
HF2SBE
the engine remove the grass-catcher and clean the channel
HF2HME
HF2HTE
6.1 SAFETY RECOMMENDATIONS
6. MAINTENANCE
Summary of the main situations where work may be required
6.2 ROUTINE MAINTENANCE
HOURS
a Periodic maintenance
HOURS
HF2315
HF2315
b Lubrication
HF2S
HF24
Blade replacement
No device other than the battery charger is to be connected
tery on your machine must be charged before using for the first time
to this connector
The charge must be maintained with the battery charger, fol
Having checked that there is nothing in
6.3 CHECKS AND ADJUSTMENTS
a Removing the cutting deck
Put the cutting height adjustment lever into the notch at position
b Dismantling, sharpening and balancing blades
gloves when handling the blades
Wear heavy
To remove a blade, hold it firmly and
When re-fitting
When installing them, make sure that they are correctly
ing screws 2 using a torque
put the height adjusting lever into
7 - 9 of the three trace rods until the deck is resting on the blocks
spring length 2 is achieved measured
Turn the adjusting nut 1 until the correct
6.3.4 BRAKE ADJUSTMENT
work properly even after this adjustment
measured inside the washers. When the adjust
great care when using for the first few times as
B = 45 - 47 mm
6.4 DISMANTLING AND REPLACEMENT
the air cleaner element. A fire or explosion could result
WARNING! Never use gasoline or low flash point solvents for cleaning
wrench special tool
6. Tighten the oil filter to the specified torque 12 Nm - 1.20 kgm
cleaner cover 2, and remove the cover
5. Reinstall the air cleaner elements and the cover
air cleaner case when servicing the air cleaner
When installing a new spark plug, tighten 1/2 turn after the
prevent an uneven cut
tightened spark plugs can become very hot and may damage the engine
carefully re-fit the snap ring 1 and washer
The wheels are held by a snap ring 1 which
1 - 10 Amps - Red
wear! ALWAYS USE GENUINE REPLACEMENT BELTS
type and rating, and never with one of another rating
PROBLEM
7. TROUBLESHOOTING
SOLUTION
LIKELY CAUSE
models with
HF2220
lever operated
engagement
have the necessary equipment and the technical knowledge
WARNING! Do not take on complicated repair work if you dont
models with
electromagnetic
1. STONE-GUARD KIT
8. ACCESSORIES OPTIONAL
2. TOWING HITCH
3. MULCHING PLUG
HF2315SBE
9. SPECIFICATIONS
HF2315HME
HF2415SBE
ALPHABETICAL INDEX
10. ALPHABETICAL INDEX