HF2315SBE HF2315HME HF2415SBE HF2417HME HF2417HTE HF2620HME HF2620HTE
Honda Europe Power Equipment S.A
TONDEUSE AUTOPORTEE LAWN-TRACTOR RASENTRAKTOR
TRATTORINO RASAERBA ZITMAAIER
INTRODUCTION
AFTER-SALES SERVICE
TABLE OF CONTENTS
death to oneself or others
1. SAFETY REGULATIONS
1.1 HOW TO READ THE MANUAL
or others
1.2 SAFETY REGULATIONS read carefully before using the machine
fumes can collect 2 Mow only in daylight or good artificial light
4 = Danger! Ejected objects
1.3 SAFETY DECALS
1.4 REGULATIONS FOR TOWING
3 = Danger! Ejected objects
tive 2000/14/EEC
HOW TO RECOGNIZE YOUR MACHINE
2. IDENTIFICATION OF THE MACHINE AND COMPONENTS
2.1 IDENTIFICATION OF THE MACHINE
2.2 IDENTIFICATION OF MAIN COMPONENTS
3. UNPACKING AND ASSEMBLY
3.1 UNPACKING
3.2 FITTING THE STEERING WHEEL
3.3 FITTING THE SEAT
3.4 FRONT BUMPER ASSEMBLY if fitted
3.5 CONNECTING THE BATTERY
same size to push the pin in the last part
uting it evenly among the six elements
To prevent the safety device in the electronics card from cut
ting in, never start the engine until the battery is fully charged
Battery acid is corrosive and a pollutant. When handling
3.7 ASSEMBLING THE LEVERS FOR TIPPING THE GRASS-CATCHER
3.8 REMOVAL OF THE STOP FROM THE HOOKING PAWL OF THE GRASS- CATCHER
3.9 GRASS-CATCHER ASSEMBLY
Page
4. CONTROLS AND INSTRUMENTS
spond to
4.7 PUSH-BUTTON FOR REVERSE MOWING
HF2SBE
HF2315HME HF2417
HF2620
a The display comes on when the key is inserted
Afterwards, when a warning light comes on, it indicates
When the machine is in movement, keep your foot off the
pedal
stopped
4.5 is engaged, the engine stops
stopped
N F N
5.2 WHY THE SAFETY DEVICES CUT IN
5. HOW TO USE
5.1 SAFETY RECOMMENDATIONS
Do not tamper with or remove the safety devices fitted to the machine
To start the engine, in all cases it is necessary that
5.3 PRELIMINARY OPERATIONS BEFORE STARTING WORK
ously. The use of a non-detergent or two-stroke
Use oil SAE 10W30 and Petrol Unleaded Euro
Running the engine with an
insufficient amount of oil can damage it very seri
The protection devices must be fitted with
the operator is absent with the parking brake disengaged
5.4 USING THE MACHINE
engine starting when the blades are engaged
the transmission is not in neutral «N»
roads. It has to be used as indicated by the Highway Code in private
areas closed to traffic
and the cutting deck put at its highest position position «7»
Reverse must be engaged ONLY when the machine is stopped
releasing the drive pedal in forward or reverse
2,5 km/h
all four wheels, WITH THE ENGINE OFF AND
THE BLADES DISENGAGED
High and dense grass - wet lawn
can only be done with the blades disengaged
The dumping switch operates
switch. To stop the signal, disengage the blades
Emptying the grass-catcher
unattended
WARNING! This job must only be performed with the engine turned off
For washing the inside of the cutting deck
Never use hose-nozzles or harsh detergents for cleaning the
do not clean the clutch with petrol
body and engine
the fuel filter
next time the machine is used
Empty the fuel tank by disconnect
ing the tube situated at the inlet of
REDUCE SPEED BEFORE ANY CHANGE OF DIRECTION
do not reverse the leads on the battery terminals
5.5 USING ON SLOPING GROUND
be careful not to cause short-circuits
5.6 TRANSPORTING
5.7 ADVICE ON HOW TO OBTAIN A GOOD CUT
HF2HME HF2HTE press the drive pedal forward
directions
Start the engine Go forward Brake or stop Reverse
Move the accelerator
HF2HTE
the engine remove the grass-catcher and clean the channel
HF2SBE
HF2HME
6.2 ROUTINE MAINTENANCE
6. MAINTENANCE
6.1 SAFETY RECOMMENDATIONS
Summary of the main situations where work may be required
HF2315
a Periodic maintenance
HOURS
HOURS
HF24
b Lubrication
HF2315
HF2S
Blade replacement
The charge must be maintained with the battery charger, fol
tery on your machine must be charged before using for the first time
No device other than the battery charger is to be connected
to this connector
6.3 CHECKS AND ADJUSTMENTS
a Removing the cutting deck
Having checked that there is nothing in
Put the cutting height adjustment lever into the notch at position
To remove a blade, hold it firmly and
gloves when handling the blades
b Dismantling, sharpening and balancing blades
Wear heavy
put the height adjusting lever into
When installing them, make sure that they are correctly
When re-fitting
ing screws 2 using a torque
7 - 9 of the three trace rods until the deck is resting on the blocks
spring length 2 is achieved measured
Turn the adjusting nut 1 until the correct
6.3.4 BRAKE ADJUSTMENT
B = 45 - 47 mm
measured inside the washers. When the adjust
work properly even after this adjustment
great care when using for the first few times as
6.4 DISMANTLING AND REPLACEMENT
6. Tighten the oil filter to the specified torque 12 Nm - 1.20 kgm
WARNING! Never use gasoline or low flash point solvents for cleaning
the air cleaner element. A fire or explosion could result
wrench special tool
cleaner cover 2, and remove the cover
5. Reinstall the air cleaner elements and the cover
air cleaner case when servicing the air cleaner
When installing a new spark plug, tighten 1/2 turn after the
The wheels are held by a snap ring 1 which
tightened spark plugs can become very hot and may damage the engine
prevent an uneven cut
carefully re-fit the snap ring 1 and washer
wear! ALWAYS USE GENUINE REPLACEMENT BELTS
type and rating, and never with one of another rating
1 - 10 Amps - Red
LIKELY CAUSE
7. TROUBLESHOOTING
PROBLEM
SOLUTION
engagement
HF2220
models with
lever operated
electromagnetic
WARNING! Do not take on complicated repair work if you dont
have the necessary equipment and the technical knowledge
models with
3. MULCHING PLUG
8. ACCESSORIES OPTIONAL
1. STONE-GUARD KIT
2. TOWING HITCH
HF2415SBE
9. SPECIFICATIONS
HF2315SBE
HF2315HME
ALPHABETICAL INDEX
10. ALPHABETICAL INDEX