INTRODUCTION IMPORTANT
PRECAUTIONS
ASSEMBLY
BEFORE
YOU BEGIN
TREADMILL
OPERATION
CONDITIONING TROUBLESHOOTING LIMITED
GUIDELINES & MAINTENANCE WARRANTY
34
M A I N T E N A N C E
Cleanliness of your treadmill and its operation environment will keep maintenance problems and service calls to a minimum. For this reason, we recommend that the following preventive maintenance schedule be followed.
AFTER EACH USE (DAILY)
Clean and inspect, following these steps:
•Turn off the treadmill with the on/off switch, then unplug the power cord at the wall outlet.
•Wipe down the running belt, deck, motor cover, and console casing with a damp cloth. Never use solvents, as they can cause damage to the treadmill.
•Inspect the power cord. If the power cord is damaged, contact Horizon Fitness.
•Make sure the power cord is not underneath the treadmill or in any other area where it can become pinched or cut.
•Check the tension and alignment of the running belt. Make sure that the treadmill belt will not damage any other components on the treadmill by being misaligned.
EVERY WEEK
Clean underneath the treadmill, following these steps:
•Turn off the treadmill with the on/off switch, then unplug the power cord at the wall outlet.
•Fold the treadmill into the upright position, making sure that the lock latch is secure.
•Move the treadmill to a remote location.
•Wipe or vacuum any dust particles or other objects that may have accumulated underneath the treadmill.
•Return the treadmill to its previous position.
EVERY MONTH - IMPORTANT!
•Turn off the treadmill with the on/off switch, then unplug the power cord at the wall outlet.
•Inspect all assembly bolts of the machine for proper tightness.
•Turn off the treadmill and wait 60 seconds.
•Remove the motor cover. Wait until all displays turn off.
•Clean the motor and lower board area to eliminate any lint or dust particles that may have accumulated. Failure to do so may result in premature failure of key electrical components.
•Vacuum and wipe down the belt with a damp cloth. Vacuum any black/white particles that may accumulate around the unit. These particles may accumulate from normal treadmill use.
EVERY 6 MONTHS OR 150 MILES |
|
|
It is necessary to lubricate your treadmill running deck every six months | L U B R I C AT I O N |
|
or 150 miles to maintain optimal performance. Once the treadmill reaches |
| |
150 miles, the console will display the message “LUBE” or “LUBE BELT”. |
| |
The treadmill will not operate while the message is showing. Hold Stop |
|
|
for 5 seconds to suspend message for 5 miles. Your treadmill came with |
|
|
|
| |
a bottle of lubricant which can be used for two applications. If you need | RUNNING BELT |
|
lubricant, contact Horizon Fitness. Only use lubricant provided by Horizon |
| |
|
| |
Fitness. |
|
|
• Turn off the treadmill with the on/off switch, then unplug the power |
|
|
cord at the wall outlet. | RUNNING DECK |
|
• Loosen both the rear roller bolts. (For best results, place two removable |
|
|
marks on both sides of the frame and note roller position). Once the |
|
|
belt is loosened, take the bottle of lubricant and apply it to the entire |
|
|
top surface of the running deck. Tighten both rear roller bolts |
|
|
(matching up the marks for proper position) to original position. After |
|
|
you have applied lubricant, plug in the power cord, insert the safety |
|
|
key, start the treadmill and walk on the belt for two minutes to spread |
|
|
the lubricant. |
|
|
• Lubricate the air shocks with Teflon based spray. |
|
|
|
|
•Once lubrication is complete, reset the console by pressing and holding ‘STOP’ and Speed ‘+’ buttons for 5 seconds. Please contact Horizon Fitness with questions about applying lubricant to your treadmill.
