Manuals / Hoshizaki / Kitchen Appliance / Freezer

Hoshizaki C-101BAH-ADDS, C-101BAH-DS instruction manual Remove the gasket from the door. See Fig

Models: C-101BAH C-101BAH-AD C-101BAH-DS C-101BAH-ADDS

1 40

Download 40 pages 30.96 Kb

Page 20

8)Remove the gasket from the door. See Fig. 17.

7)Remove the bushings from hinge (C1) and hinge (C2) (the hinges attached to the door). See Fig. 16.

8)Remove the gasket from the door. See Fig. 17.

BushingGasket

Hinge

Fig. 16

Fig. 17

9)Temporarily fasten the overlay panel to the door using 2 of the M4×25 pan head screws provided. NOTICE! Ensure that the back surface of overlay panel is flat before attaching. See Fig. 18.

10)Mark the centerpoint of the hinge (C1) and hinge (C2) holes that extend over the overlay panel. See Fig. 19.

11)Remove the overlay panel from the door.

Screws

Hinge

Door

Overlay Panel

Mark the center point.

Fig. 18

Fig. 19

12)Drill 3/8" diameter holes 1/4" (7 mm) deep where you marked on the overlay panel to accommodate the hinge (C1) and hinge (C2) bushings.

20

Image 20

Hoshizaki C-101BAH-ADDS, C-101BAH-DS instruction manual Remove the gasket from the door. See Fig

Contents

Self-Contained Cubelet Models C-101BAH C-101BAH-DS C-101BAH-AD HoshizakiHoshizaki America, IncComplete and detailed explanation of the problem Phone 1-800-233-1940 770 Fax618 Highway 74 South Peachtree City, GA Attn Hoshizaki Technical Support DepartmentCONTENTS Important Safety Information Indicates important information about the installation, use, andIndicates a hazardous situation which could result in death or serious injuryWARNING, continued I. Specifications A. Construction B. Electrical and Refrigerant DataModel Number C-101BAHC. Dimensions/Connections 1. C-101BAH2. C-101BAH-DS Units mm in3. C-101BAH-AD Units mm in4. C-101BAH-ADDS Units mm inII. Installation Instructions A. Checks Before InstallationB. Location 1. General2. Built-In Installation Site Between Two CabinetsBetween a Cabinet and the End of a Countera Door Reversal C. Door1. C-101BAH, C-101BAH-AD 4 Remove hinge B from the right side of the appliance and the 2 filler screws from the left side. Attach the 2 filler screws to the right side and attach hinge B to the left side. See Fig 1 Parts 2. C-101BAH-DS, C-101BAH-ADDSa Overlay Panel Fabrication and Attachment 2 Overlay Panel Specification C-101BAH-DS Overlay Panel SpecificationC-101BAH-ADDS Overlay Panel Specification Overlay Panel and Door Weight totalb C-101BAH-ADDS Overlay Panel Height3 Fabrication of Overlay Panel 6 If you would like to reverse the door hinges, do the following 8 Remove the gasket from the door. See Fig 4 Attachment of Overlay Panel to Door 7 Tighten the four M4×25 pan head screws installed in step 5. See Fig D. Setup E. Electrical ConnectionF. Water Supply and Drain Connections For gravity drain installation, drain must have 1/4 fall per foot 2 cm per 1 m on horizontal runs to get good flow. A vented tee connection is also required for proper flow. Extend the vent at least 12 30 cm above the drain outlet G. Final Checklist III. Operating Instructions A. Important Notes About Usage Do not place objects on top of the appliance B. Startup IV. Maintenance A. Maintenance Schedule Maintenance ScheduleFrequency Area2. Cleaning Procedure B. Cleaning and Sanitizing Instructions1. Cleaning Solution 3. Sanitizing Solution 4. Sanitizing Procedure - Initial5. Sanitizing Procedure - Final C. Storage Bin DrainD. Condenser E. Optional Drain Pump HS-5061 Discharge HoseUpper Rear Panel V. Preparing the Appliance for Periods of Non-UseReservoir Clamp Reservoir Outlet Hose Overflow Hose 18 Replace the rear panel in its correct position VI. Disposal HOSHIZAKI AMERICA, INC