Manuals / Hoshizaki / Kitchen Appliance / Freezer

Hoshizaki C-101BAH-AD I. Specifications A. Construction, B. Electrical and Refrigerant Data

Models: C-101BAH C-101BAH-AD C-101BAH-DS C-101BAH-ADDS

1 40

Download 40 pages 30.96 Kb

Page 6

I. Specifications

I. Specifications

A. Construction

Top Panel

Ice Discharge

Opening

Scoop Holder

Slope

Front Panel

Control Switch

Power Cord

Louver

Bin Control

Thermostat

Bulb

Magnet

Catch

Door

B. Electrical and Refrigerant Data

The nameplate provides electrical and refrigerant data. The nameplate is located inside the storage bin. For certification marks, see the nameplate.

We reserve the right to make changes in specifications and design without prior notice.

Model Number	C-101BAH
	C-101BAH-DS
	C-101BAH-AD
	C-101BAH-ADDS
AC Supply Voltage	115-120/60/1
Amperes	4.0 AMPS
Design Pressure	HI-240PSI LO-120PSI
Refrigerant	134a 3.17 OZ.

6

Image 6

Hoshizaki C-101BAH-AD I. Specifications A. Construction, B. Electrical and Refrigerant Data, Model Number, C-101BAH-DS

Contents

Self-Contained Cubelet Models C-101BAH C-101BAH-DS C-101BAH-AD HoshizakiHoshizaki America, Inc618 Highway 74 South Peachtree City, GA Complete and detailed explanation of the problemPhone 1-800-233-1940 770 Fax Attn Hoshizaki Technical Support DepartmentCONTENTS Indicates a hazardous situation which could result in death or Important Safety InformationIndicates important information about the installation, use, and serious injuryWARNING, continued Model Number I. Specifications A. ConstructionB. Electrical and Refrigerant Data C-101BAHC. Dimensions/Connections 1. C-101BAH2. C-101BAH-DS Units mm in3. C-101BAH-AD Units mm in4. C-101BAH-ADDS Units mm inB. Location II. Installation InstructionsA. Checks Before Installation 1. GeneralBetween a Cabinet and 2. Built-In Installation SiteBetween Two Cabinets the End of a CounterC. Door 1. C-101BAH, C-101BAH-ADa Door Reversal 4 Remove hinge B from the right side of the appliance and the 2 filler screws from the left side. Attach the 2 filler screws to the right side and attach hinge B to the left side. See Fig 2. C-101BAH-DS, C-101BAH-ADDS a Overlay Panel Fabrication and Attachment1 Parts 2 Overlay Panel Specification C-101BAH-DS Overlay Panel Specificationb C-101BAH-ADDS C-101BAH-ADDS Overlay Panel SpecificationOverlay Panel and Door Weight total Overlay Panel Height3 Fabrication of Overlay Panel 6 If you would like to reverse the door hinges, do the following 8 Remove the gasket from the door. See Fig 4 Attachment of Overlay Panel to Door 7 Tighten the four M4×25 pan head screws installed in step 5. See Fig D. Setup E. Electrical ConnectionF. Water Supply and Drain Connections For gravity drain installation, drain must have 1/4 fall per foot 2 cm per 1 m on horizontal runs to get good flow. A vented tee connection is also required for proper flow. Extend the vent at least 12 30 cm above the drain outlet G. Final Checklist III. Operating Instructions A. Important Notes About Usage Do not place objects on top of the appliance B. Startup IV. Maintenance Frequency A. Maintenance ScheduleMaintenance Schedule AreaB. Cleaning and Sanitizing Instructions 1. Cleaning Solution2. Cleaning Procedure 3. Sanitizing Solution 4. Sanitizing Procedure - Initial5. Sanitizing Procedure - Final C. Storage Bin DrainD. Condenser E. Optional Drain Pump HS-5061 Discharge HoseV. Preparing the Appliance for Periods of Non-Use Reservoir Clamp Reservoir Outlet Hose Overflow HoseUpper Rear Panel 18 Replace the rear panel in its correct position VI. Disposal HOSHIZAKI AMERICA, INC