Manuals / Hoshizaki / Kitchen Appliance / Ice Maker

Hoshizaki M029-897 Water Pan, Refer to illustration for assembly, Assembly, Water Tank, Bracket

Models: M029-897

1 39

Page 33

Water Pan	Refer to illustration for assembly.
Assembly		1. Water Tank
		1. Water Tank
		2. Water Plate Bracket
		3. Bracket
		4. Spring Hook Screw
		5. Pump Tubing (Suction)
		6. Pump Tubing (Discharge)
		7. Pump Motor Bracket
		8. Water Plate
		9. Overflow Pipe
		10. Screw (for Overflow Pipe)
		11. Nylon Tie
		12. O-ring
		J. Pump Motor Assembly
		S1-4. Tapping Screw
		S5. Machine Screw

Icemaking	Refer to illustration for assembly.	G. Water Pan Assembly
Assembly and		1. Evaporator
Cam Mechanism		2. Bolt
		2. Bolt
		3. Collar (Spacer)
		4. Bearing
		5. Actuator Motor
		7. Shaft
		9. Actuator Motor Bracket
		10. Cam Shaft Bearing
		11. Spring Pin
		13. Cam Arm (B)
		14. Cam Shaft
		15. Snap Pin
		16. Split Pin
		17. Spring
		18. Washer (A)
		19. Washer (B)
		20. Washer (C)
		21. Thermistor Holder
		22. Label (for Overflow Pipe)
		23. Thermistor (Cube Control)
		26. Frame
		27. Frame
		28. Wire Saddle
		29. Washer
		30. Cam Arm (A)
		31. Change Lever
		S1-5. Machine Screw

Page 33

Image 33

Hoshizaki M029-897 Water Pan, Refer to illustration for assembly, Assembly, Water Tank, Water Plate Bracket, Overflow Pipe

Contents

Stackable Square Cuber Model IM-500SAA HoshizakiHoshizaki America, IncPhone 1-800-233-1940 770 Fax Complete and detailed explanation of the problem618 Highway 74 South Peachtree City, GA Attn Hoshizaki Technical Support DepartmentCONTENTS serious injury Important Safety InformationIndicates a situation which could result in damage to the appliance or propertyWARNING, continued I. Construction and Water/Refrigeration Circuit Diagram A. Construction1. Air-Cooled Model SAA B. Water/Refrigeration Circuit Diagram 1. Air-Cooled Model SAAWater Tank A. Sequence of Operation Flow Chart II. Sequence of Operation and Service DiagnosisShutdown and Restart Sequence Flow Chart IM Control Board1. Startup Cycle B. Sequence of Operation2. Harvest Cycle 3. Freeze Cycle4. Shutdown No Ice Production - Possible Cause C. Service Diagnosis TableLong Harvest Cycle Low Ice Production - Possible CauseLong Freeze Cycle Slab Does Not Break Into Separate Cubes - Possible CauseCloudy Cubes - Possible Cause Large-Hole Cubes - Possible Cause Also see III.H.1. Dimple Diameter1. Bin Control Check D. Bin Control Check and Cleaning2. Bin Control Cleaning E. Evaporator Thermistor Check B. Control Board III. Controls and Adjustments A. Control Switch1. Control Board Layout IM Control BoardPart Number P01873-01 Version 1.3A or Later 1. RESET Button 2. SERVICE 1 and SERVICE 2 ButtonsC. Control Buttons D. Control Board Settings DO NOT ADJUST Control Board CB Setting MenuDO NOT ADJUST DO NOT ADJUSTDO NOT ADJUST Control Board CB Setting MenuDO NOT ADJUST IM-500SAA2. Use the SERVICE 1 and SERVICE 2 buttons to move through the list E. Control Board Information Display3. Press the RESET button to view the item’s value 4. Press the RESET button to return to listFreeze cycles interrupted by bin control shutdown example, 655,350 cycles1.0A, displays as follows F. Control Board Model Code Setting 1. Control Board Replacement2. Checking or Changing the Control Board Model Code Page G. Error Codes 1. Dimple Diameter H. Quick Adjustmentsa To increase dimple diameter b To decrease dimple diameter2. Ice Clarity Normal PositionDrain Position IV. Refrigeration Circuit and Component Service Information A. Refrigeration Circuit Service Information1. Refrigerant Recovery 3. Evacuation and Recharge R-404A 2. BrazingB. Component Service Information Assembly Refer to illustration for assemblyJ. Pump Motor Assembly Refer to illustration for assemblyV. Maintenance VI. Preparing the Icemaker for Periods of Non-Use 1. Remove the water from the icemaker water supply line2. Drain the water tank VII. Disposal A. Specification Data VIII. Technical Information1. IM-500SAA 1. IM-500SAA B. Performance Data1. IM-500SAA C. Wiring Diagram

Water Pan

Refer to illustration for assembly.

Assembly

1. Water Tank

2. Water Plate Bracket

3. Bracket

4. Spring Hook Screw

5. Pump Tubing (Suction)

6. Pump Tubing (Discharge)

7. Pump Motor Bracket

8. Water Plate

9. Overflow Pipe

10. Screw (for Overflow Pipe)

11. Nylon Tie

12. O-ring

J. Pump Motor Assembly

S1-4. Tapping Screw

S5. Machine Screw

Icemaking

G. Water Pan Assembly

Assembly and

Cam Mechanism

2. Bolt

3. Collar (Spacer)

4. Bearing

5. Actuator Motor

7. Shaft

9. Actuator Motor Bracket

10. Cam Shaft Bearing

11. Spring Pin

13. Cam Arm (B)

14. Cam Shaft

15. Snap Pin

16. Split Pin

17. Spring

18. Washer (A)

19. Washer (B)

20. Washer (C)

21. Thermistor Holder

22. Label (for Overflow Pipe)

23. Thermistor (Cube Control)

26. Frame

27. Frame

28. Wire Saddle

29. Washer

30. Cam Arm (A)

31. Change Lever

S1-5. Machine Screw