Release Notes for 07.8.04

 

 

Software Fixes

 

 

 

 

 

Bug ID

Bug Description

Protocol/

Version

Version

 

 

Feature

Found

Fixed

 

 

 

 

 

47254

On an EP 8 Port Mini-GBIC Redundant

ACL

 

07.8.02

 

Management module, when you configure sFlow

 

 

 

 

and an ACL so that packets that were being

 

 

 

 

forwarded by the CPU are filtered by the ACL, an

 

 

 

 

incorrect VLAN ID is matched with the ACL.

 

 

 

 

 

 

 

 

47542

A system reload may occur when you enter a show

ACL/Telnet

 

07.8.02

 

run command during a Telnet session in which you

 

 

 

 

bind ACLs to a port.

 

 

 

 

 

 

 

 

47724

When you enter the show ip bgp neighbor <x>

BGP

 

07.8.02

 

adv command, all advertised routes are not always

 

 

 

 

displayed, although the routes are advertised

 

 

 

 

correctly.

 

 

 

 

 

 

 

 

47725

On an EP 48-Port 10/1000-TX RJ45 module,

Rate Limiting

 

07.8.02

 

binding and unbinding a single ACL-based rate

 

 

 

 

limiting policy too many times causes memory

 

 

 

 

corruption and results in a system reload.

 

 

 

 

 

 

 

 

48474

On an EP 8 Port Mini-GBIC Redundant

MRP2

 

07.8.02

 

Management module, when MRP2 is enabled and

 

 

 

 

hellos are sent, a member ring blocked the port,

 

 

 

 

instead of processing and forwarding hellos. Only

 

 

 

 

the master ring should block the port.

 

 

 

 

 

 

 

 

48521

On an EP 8 Port Mini-GBIC Redundant

MRP

 

07.8.02

 

Management module, disabling a port on one MRP

 

 

 

 

ring causes a port on a different ring in a blocking

 

 

 

 

state to transit through the forwarding state.

 

 

 

 

 

 

 

 

48525

On an EP 8 Port Mini-GBIC Redundant

MRP

 

07.8.02

 

Management module, you are not allowed to

 

 

 

 

configure a static trunk if the ports in the trunk are

 

 

 

 

members of an MRP2 ring.

 

 

 

 

 

 

 

 

48587

On an EP 8 Port Mini-GBIC Redundant

MRP

 

07.8.02

 

Management module, when you change the

 

 

 

 

primary and secondary port of a lower priority ring,

 

 

 

 

ports on the higher priority ring are affected.

 

 

 

 

 

 

 

 

48660

On an EP 8 Port Mini-GBIC Redundant

System

 

07.8.02

 

Management module, after an SSH key is

 

 

 

 

generated, you are incorrectly prompted for a

 

 

 

 

configuration change immediately after you enter

 

 

 

 

the write memory command.

 

 

 

 

 

 

 

 

48747

When you reboot a routing switch with an EP 48-

MRP

 

07.8.02

 

Port 10/1000-TX RJ45 module on which MRP is

 

 

 

 

configured, a debug error message is displayed on

 

 

 

 

neighbor devices, even after a neighbor has

 

 

 

 

stabilized.

 

 

 

 

 

 

 

 

48753

On an EP 8 Port Mini-GBIC Redundant

MRP

 

07.8.02

 

Management module, 10 seconds to 3 minutes are

 

 

 

 

required for traffic to recover after a failed MRP link

 

 

 

 

returns to a forwarding state.

 

 

 

 

 

 

 

 

37