Software Fixes |
|
| Release Notes for 07.8.04 | |||
|
|
|
|
|
|
|
| Bug ID |
| Bug Description | Protocol/ | Version | Version |
|
|
|
| Feature | Found | Fixed |
|
|
|
|
|
|
|
| 59468 |
| If OSPF is configured, the OSPF configuration is | OSPF |
| 07.8.02 |
|
|
| not displayed in show ip ospf config command |
|
|
|
|
|
| output until the configuration is saved and the |
|
|
|
|
|
| switch is rebooted. |
|
|
|
|
|
|
|
|
|
|
| 59698 |
| If SSH is configured, a system reload sometimes | SSH |
| 07.8.02 |
|
|
| occurs due to insufficient stack space. |
|
|
|
|
|
|
|
|
|
|
| 59925 |
| The incorrect deletion of CAM entries may cause a | System |
| 07.8.02 |
|
|
| routing switch to reload. |
|
|
|
|
|
|
|
|
|
|
| 60117 |
| If you enable the VSRP and CPU Protection | VSRP |
| 07.8.02 |
|
|
| features, when a link flaps, the VSRP forwarding |
|
|
|
|
|
| state is not correctly set. As a result, the CAM for |
|
|
|
|
|
| the master is not updated correctly, resulting in a |
|
|
|
|
|
| Layer 2 packet loop. |
|
|
|
|
|
|
|
|
|
|
| 60227 |
| When you configure an incorrect speed on a virtual | System |
| 07.8.02 |
|
|
| interface, the valid physical port is not checked, |
|
|
|
|
|
| resulting in a system reload. |
|
|
|
|
|
|
|
|
|
|
| 60249 |
| If BGP4 is configured and a BGP update is received | BGP4 |
| 07.8.02 |
|
|
| for an existing prefix, in some cases the BGP route |
|
|
|
|
|
| does not include the BGP tree node. This can |
|
|
|
|
|
| cause the system to reload. |
|
|
|
|
|
|
|
|
|
|
| 60330 |
| If a large number of VLANs are configured, when | System |
| 07.8.02 |
|
|
| you remove or add a tagged port from a VLAN, high |
|
|
|
|
|
| CPU utilization occurs. |
|
|
|
|
|
|
|
|
|
|
| 60396 |
| When a static MAC address is configured on | System |
| 07.8.02 |
|
|
| multiple ports, the address is not displayed on all |
|
|
|
|
|
| ports in show mac ethernet <slot/port> command |
|
|
|
|
|
| output. |
|
|
|
|
|
|
|
|
|
|
| 60401 |
| When you configure a username password using all | System |
| 07.8.02 |
|
|
| numeric characters, it is necessary to |
|
|
|
|
|
| service |
|
|
|
|
|
| add each password. |
|
|
|
|
|
| To create an MD5 password, use one of the |
|
|
|
|
|
| following commands: |
|
|
|
|
|
| • username <username> |
|
|
|
|
|
|
|
|
| |
|
|
| • username <username> privilege <number> |
|
|
|
|
|
|
|
|
| |
|
|
| Both commands generate the same syntax. |
|
|
|
|
|
| • username <username> password <number> |
|
|
|
|
|
|
|
|
| |
|
|
| Or |
|
|
|
|
|
| • username <username> privilege <number> |
|
|
|
|
|
| password <number> |
|
|
|
|
|
| string> |
|
|
|
|
|
|
|
|
|
|
44