Release Notes for 07.8.04 |
|
| Software Fixes | |
|
|
|
|
|
Bug ID | Bug Description | Protocol/ | Version | Version |
|
| Feature | Found | Fixed |
|
|
|
|
|
60916 | Traffic is not evenly balanced on the members of a | IP Routing |
| 07.8.02 |
| trunk after you enter the ip |
|
|
|
| command and configure multislot switch trunks. |
|
|
|
|
|
|
|
|
60979 | If BGP4 is configured and you enter the remove | BGP4 |
| 07.8.02 |
|
|
|
| |
| that the routing switch receives an update from a |
|
|
|
| private AS for which it is configured, the BGP |
|
|
|
| update is sent out with the AS numbers stripped |
|
|
|
| out. |
|
|
|
| If the AS numbers are private only, the AS path |
|
|
|
| attribute will be empty. This causes the neighbor to |
|
|
|
| reset the BGP peering. |
|
|
|
|
|
|
|
|
61211 | If you configure a Gigabit fiber port using the | System |
| 07.8.02 |
| gigabit auto rfn command, and the port is |
|
|
|
| physically connected and then disconnected to a |
|
|
|
| Cisco router, the port does not always come up. |
|
|
|
|
|
|
|
|
61383 | When an ACL is configured, the ip | ACL |
| 07.8.02 |
| in ethernet <slot/port> command does not correctly |
|
|
|
| apply the ACL to only the specified port. |
|
|
|
|
|
|
|
|
61434 | When the STP boundary is changed dynamically, | Spanning Tree |
| 07.8.02 |
| the new value is not displayed in show superspan |
|
|
|
| command output. |
|
|
|
| The workaround is to remove the value by entering |
|
|
|
| the no |
|
|
|
| configuring a new value. |
|
|
|
|
|
|
|
|
61501 | If a spanning tree is configured and a port is tagged | Spanning Tree |
| 07.8.02 |
| for the default VLAN, the spanning tree state on the |
|
|
|
| default VLAN is not updated. As a result, the |
|
|
|
| outbound traffic is forwarded on the blocked port |
|
|
|
| causing a loop. |
|
|
|
|
|
|
|
|
62071 | If OSPF is configured and there are multiple | OSPF |
| 07.8.02 |
| neighbors on an interface, the OSPF routes are not |
|
|
|
| learned from the interface unless all the neighbors |
|
|
|
| are established. |
|
|
|
|
|
|
|
|
62367 | If VSRP is configured, port indication on a change | VSRP |
| 07.8.02 |
| in the port state incorrectly programs forwarding |
|
|
|
| information. As a result, port 1/1 does not send |
|
|
|
| outbound traffic. |
|
|
|
|
|
|
|
|
62826 | If UDLD is configured, an incorrect error message | UDLD |
| 07.8.02 |
| may be displayed: |
|
|
|
|
|
|
| |
| cannot be enabled. |
|
|
|
|
|
|
|
|
62893 | If the primary port of the trunk goes down due to a | Port Security |
| 07.8.02 |
| port security violation, the other members of the |
|
|
|
| trunk are displayed incorrectly as “state: Down”. |
|
|
|
|
|
|
|
|
45