Husky HDS550 Operation, Maintenance, WATER/OIL in Compressed AIR, Daily CLEAN-UP, 22 Sp

Manual de Instrucciones y Lista de Piezas		HDS550
Sirvase darnos la siguiente información:		Puede escribirnos a:
-	Número del modelo	Campbell Hausfeld
		Attn: Parts Department
-	Código estampado en la unidad
		100 Production Drive
- Descripción y número del repuesto según la lista de repuestos
		Harrison, OH 45030

Operating Instructions and Parts Manual HDS550

Lista De Repuestos

No.		Número
de		del
Ref.	Descripción	Repuesto	Ctd.
1	Conjunto de boquilla de aire	DH067300AV	1
2	Boquilla de líquido	▲ DH067400AV 1
3	Gatillo	●	1

No.		Número
de		del
Ref.	Descripción	Repuesto	Ctd.
22	Tuerca del control de patrón	❍	1
23	Perilla del control de patrón	❍	1
24	Conjunto de tubo de material	❒	1

Preparation (Cont.)

Fluid Control

Knob

WATER/OIL IN COMPRESSED AIR

All compressor pumps discharge some condensed water, oil or contaminates with the compressed air.

IMPORTANT: This condensation will cause “fish eyes” to appear in the paint job. Install appropriate water/oil removal equipment and controls as necessary for the intended application.

Failure to install appropriate water/oil removal equipment may result in damage to machinery or workpiece.

4	Cuerpo de pistola	no disponible	1
5	Empaque de válvula de aire	■ ◆	2
6	Tuerca de empaque de válvula de aire	■ ◆	1
7	Conjunto de vástago de válvula de aire	■	1
8	Resorte de válvula de aire	■	1
9	Entrada de aire	■	1
10	Empaque de aguja de líquido	▲ ◆	2
11	Tuerca de empaque	▲	1
12	Tornillo de gatillo	●	1
14	Conjunto de aguja de líquido	▲	1
15	Resorte de control de líquido	▲	1
16	Perilla de control de líquido	▲	1
17	Pasador del control de patrón	❍	1
18	Arandela del control de patrón	❍ ◆	1
19	Resorte del control de patrón	❍	1
20	Aro de empaque del control de patrón	❍ ◆	1
21	Empaque del control de patrón	❍ ◆	1

25	Yugo	❒	1
26	Palanca de regulación	❒	1
27	Cubierta de taza	❒	1
28	Tuerca	❒	1
29	Empaquetadura (paquete de 3)	DH067500AV	1
30	Bote	DH067600AV	1

JUEGOS DE SERVICIO (contienen uno de cada componente,

salvo que se indique otra cantidad)

■Juego de válvula de aire (cant. 2 – No. 5) DH550100AV

▲	Juego de control de líquido	DH550200AV
	(cant. 2 – No. 10)
❍	Conjunto de control de patrón	DH550300AV
◆	Juego de empaquetaduras	DH550400AV
	(cant. 2 – No. 5 y No. 10)
●	Juego de gatillo	DH550500AV
❒	Conjunto de yugo	DH550600AV

Figure 2 - Adjustment on Spray Gun

3.Trigger a short burst while turning fluid control knob counterclockwise. Observe the spray pattern on the tar- get and adjust the fluid control knob until the desired pattern (atomiza- tion) is obtained.

If the spray is too fine (excessive over- spray), caused by too much air for the amount of paint being sprayed, reduce the air pressure or open the fluid con- trol to spray more material.

Paint too	Correct	Paint too
fine		coarse

Figure 3 - Pattern Consistency

(Atomization)

If the spray is too coarse (spitting globs), reduce the amount of material with the fluid control knob or thin the paint.

Before spraying the workpiece, practice a few minutes on a cardboard target to ensure the pattern size and consistency are set correctly.

Operation

while spraying. Stopping gun movement in mid-stroke will cause a build up of paint and result in “runs.” Do not “fan” the gun from side to side while painting. This will cause a build-up of paint in the center of the stroke and an insufficient coating at each end (See Figure 5).

Thin coat Heavy coat Thin coat

Figure 5

2.“Trigger” the gun properly. Start the gun moving at the beginning of the stroke BEFORE SQUEEZING THE TRIGGER and release the trigger

BEFORE STOPPING GUN MOVEMENT at the end of the stroke. This pro- cedure will “feather” (blend) each stroke with the next without show- ing overlap or unevenness).

6 - 9”
Pull	Release

5.Use a piece of cardboard as a shield to catch overspray at the edges of the work to protect other surfaces. Use masking tape to cover other areas if needed.

Figure 7

Maintenance

DAILY CLEAN-UP

Local codes may require specific clean- ing methods and equipment. Follow local codes and manufacturer’s recom- mendations for the use and disposal of spray materials and solvent.

Clean spray gun

immediately after use. Paint and other material dry quickly in the small pas- sages rendering gun useless due to the difficulty of removing hardened paint from the passages inside the gun.

NOTE: In the instructions below, the use of the word “solvent” refers to the specific solvent for the material used (eg:

1.Begin spray- ing. Always keep the gun at right angles to the work. (See Figure 4.)

Keep the nozzle about 6 to 9 inches from the work surface through- out the stroke and always keep the gun in motion

6 - 9”

Figure 4

Trigger	Trigger
Start	End
Stroke	Stroke
Figure 6

3.The amount of paint being applied can be varied by the speed of the stroke, distance from the surface and adjustment of the fluid control knob.

4.Overlap strokes just enough to obtain an even coat. NOTE: Two thin coats of paint will yield better results and have less chance of runs than one heavy layer.

lacquer thinner for lacquer, etc ).

1.Remove and empty the canister; then rinse with a solvent recommended for the paint or other material used.

2.Refill canister with clean solvent and attach to the gun. Spray solvent through the gun while shaking the gun vigorously. Wipe the gun exteri- or with a solvent soaked rag. Repeat until the gun is clean.

22 Sp

3