Manuals / Husqvarna / Lawn and Garden / Lawn Mower

Husqvarna 11 Bio/13 H Bio Lever for adjustment of cutting height, Seat, Fuelling, Rider 13 H

Models: 11 Bio/13 H Bio

1 43

Download 43 pages 52.23 Kb

Page 12

Image 12

PRESENTATION

Lever for adjustment of cutting height

With this lever the cutting height can be adjusted to 9 different positions.

Cutting unit with rear ejection,	40-90 mm.
BioClip cutting unit,	45-95 mm.

Rider 13 H

Seat

The seat has a jointed attachment on the front edge and can be tipped forward.

The seat can also be adjusted lengthways.

Release the knobs under the seat and adjust it forwards or backwards to the required position.

Lock the adjustment with the wheels.

Fuelling

The engine should be run on 85 octane (or higher) unleaded petrol/gasoline (no added oil). Environ- mentally adapted alkylate fuel, such as Aspen, is also recommended.

!WARNING!

Petrol/gasoline is highly inflammable. Observe care and fill up with fuel outdoors (see safety instructions).

English – 11

Page 12

Image 12

Husqvarna 11 Bio/13 H Bio manual Lever for adjustment of cutting height, Seat, Fuelling, Rider 13 H, Presentation

Contents

101 Rider 11/13 H Rider 11 Bio/13 H BioOperator´s manual CONTENTS Operator’s Manual for Rider 11 and Rider 13 H Rider 11 Bio and Rider 13 H BioIMPORTANT INFORMATION Travel and transport on public roadsEXPLANATION OF SYMBOLS SAFETY INSTRUCTIONS General useRead the instructions before starting the machine Clear the area from stones etc. before cuttingBe extra careful when driving on slopes Driving on slopesDo as follows Cut slopes upwards and downwards, not sidewaysMaintenance ChildrenKeep children away from the mowing area Never allow children to drive the machineClean the machine regularly from grass, leaves and other waste SAFETY INSTRUCTIONSbattery can explode and cause severe injuries before starting the engine. If fuel is spilt on clothes, change themPRESENTATION PresentationLocation of the controls PRESENTATION RIDER 11 / 11 BIO Throttle and Choke leverClutch pedal Brake pedal / Parking brakePRESENTATION RIDER 13 H / 13 H BIO Speed limiterParking brake Throttle and Choke leverCutting unit Lift lever for cutting unitRider 11 Bio and Rider 13 H Bio have a twin-blade Lifting of the cutting unit transport positionLever for adjustment of cutting height SeatFuelling Rider 13 HDRIVING Before startingStarting the engine Rider 13 HCold engine Warm engineDRIVING 5. Set the throttle control midway between position 1 andDriving the machine 2. For Rider 13 H and Rider 13 H BioFor Rider 11 and Rider 11 Bio The clutch must be used for each gear changeCutting tips Mowing patternDRIVING IMPORTANT INFORMATIONHill start, manual gearbox Stopping the engineRelease lever Rider 13 H and Rider 13 H Bio DRIVINGMAINTENANCE Maintenance scheduleMaintenance interval MaintenanceDismantling of the machine hoods Engine hoodFront hood Rider 11 and Rider 13 H Front hood Rider 11 Bio and Rider 13 H BioRight-hand fender Left-hand fenderMAINTENANCE Release the screws in the fender and lift off the fenderCheck the engine’s oil level Check the engine’s cooling air intakeChecking of the fuel pump’s air filter MAINTENANCEChecking and adjustment of the steering wires MAINTENANCEAdjusting the brake Rider 11 and Rider 11 Bio Check and adjust the brakes on Rider 13 H and Rider 13 H BioPoorly adjusted brakes can result in reduced braking power Checking the brake Rider 11 and Rider 11 BioCheck the level of the battery acid Check the safety systemProcedures on contact with acid Check the transmission’s oil level Rider 13 H and Rider 13 H BioDo not use compressed air to clean the paper filter Replacing the air filterMAINTENANCE IMPORTANT INFORMATIONChecking the cutting unit’s parallelism MAINTENANCEAdjustment of the cutting unit’s parallelism MAINTENANCEMAINTENANCE RIDER 11/11 BIO Service position for BioClipPlacing in service position MAINTENANCE RIDER 11/11 BIO 5. Disengage the spring from the drive belt tensioning wheelRestoring from service position MAINTENANCE RIDER 11/11 BIO7. Lift off the drive belt 1. Then pull out the pin Take care not to get your hand trappedChecking the blades Checking the tyre pressureCutting unit rear ejection Bio MAINTENANCEChanging the oil Lubrication Rider 11 and Rider 11 BioLubrication of front wheel bearings Check that the lock-ring is correctly posi- tioned in the slotLubrication of belt tensioner General lubricationMAINTENANCE 32 - EnglishChecking and adjustment of the throttle wire Replacement of the fuel filterMAINTENANCE TROUBLE SHOOTING SCHEDULE ProblemProcedure Service STORAGEWinter storage TECHNICAL DATA DimensionsRider Rider 13 HRider 11 Bio Rider 13 H BioTECHNICAL DATA DimensionsEU declaration of conformity Only applies to Europe Directive 89/392/EEC, Annex II, ASvenska ´*3,¶6X¨ Svenska 2000W37 ´*3,¶6X¨