Manuals / Husqvarna / Lawn and Garden / Lawn Mower

Husqvarna 11 Bio/13 H Bio manual Lubrication of belt tensioner, General lubrication, Maintenance

Models: 11 Bio/13 H Bio

1 43

Download 43 pages 52.23 Kb

Page 33

Image 33

MAINTENANCE

Lubrication of belt tensioner

The belt tensioner must be lubricated regularly with high-quality molybdenum sulphide grease.

Inject grease into the nipple on the right side below the engine bottom pulley until grease is forced out.

With daily use lubrication should be conducted twice a week.

General lubrication

All joints and bearings are lubricated on manufac- ture with molybdenum sulphide grease. Re-grease with same type of grease. Lubricate the steering and control wires with engine oil.

The machine should be lubricated regularly, and twice a week when used daily.

32 – English

Page 33

Image 33

Husqvarna 11 Bio/13 H Bio manual Lubrication of belt tensioner, General lubrication, Maintenance, English

Contents

101 Rider 11/13 H Rider 11 Bio/13 H BioOperator´s manual Rider 11 Bio and Rider 13 H Bio CONTENTS Operator’s Manual for Rider 11 and Rider 13 HIMPORTANT INFORMATION Travel and transport on public roadsEXPLANATION OF SYMBOLS General use SAFETY INSTRUCTIONSRead the instructions before starting the machine Clear the area from stones etc. before cuttingDriving on slopes Be extra careful when driving on slopesDo as follows Cut slopes upwards and downwards, not sidewaysChildren MaintenanceKeep children away from the mowing area Never allow children to drive the machineSAFETY INSTRUCTIONS Clean the machine regularly from grass, leaves and other wastebattery can explode and cause severe injuries before starting the engine. If fuel is spilt on clothes, change themPRESENTATION PresentationLocation of the controls Throttle and Choke lever PRESENTATION RIDER 11 / 11 BIOClutch pedal Brake pedal / Parking brakeSpeed limiter PRESENTATION RIDER 13 H / 13 H BIOParking brake Throttle and Choke leverLift lever for cutting unit Cutting unitRider 11 Bio and Rider 13 H Bio have a twin-blade Lifting of the cutting unit transport positionSeat Lever for adjustment of cutting heightFuelling Rider 13 HBefore starting DRIVINGStarting the engine Rider 13 HWarm engine Cold engineDRIVING 5. Set the throttle control midway between position 1 and2. For Rider 13 H and Rider 13 H Bio Driving the machineFor Rider 11 and Rider 11 Bio The clutch must be used for each gear changeMowing pattern Cutting tipsDRIVING IMPORTANT INFORMATIONStopping the engine Hill start, manual gearboxRelease lever Rider 13 H and Rider 13 H Bio DRIVINGMaintenance schedule MAINTENANCEMaintenance interval MaintenanceEngine hood Dismantling of the machine hoodsFront hood Rider 11 and Rider 13 H Front hood Rider 11 Bio and Rider 13 H BioLeft-hand fender Right-hand fenderMAINTENANCE Release the screws in the fender and lift off the fenderCheck the engine’s cooling air intake Check the engine’s oil levelChecking of the fuel pump’s air filter MAINTENANCEMAINTENANCE Checking and adjustment of the steering wiresCheck and adjust the brakes on Rider 13 H and Rider 13 H Bio Adjusting the brake Rider 11 and Rider 11 BioPoorly adjusted brakes can result in reduced braking power Checking the brake Rider 11 and Rider 11 BioCheck the safety system Check the level of the battery acidProcedures on contact with acid Check the transmission’s oil level Rider 13 H and Rider 13 H BioReplacing the air filter Do not use compressed air to clean the paper filterMAINTENANCE IMPORTANT INFORMATIONMAINTENANCE Checking the cutting unit’s parallelismMAINTENANCE Adjustment of the cutting unit’s parallelismMAINTENANCE RIDER 11/11 BIO Service position for BioClipPlacing in service position 5. Disengage the spring from the drive belt tensioning wheel MAINTENANCE RIDER 11/11 BIOMAINTENANCE RIDER 11/11 BIO Restoring from service position7. Lift off the drive belt 1. Then pull out the pin Take care not to get your hand trappedChecking the tyre pressure Checking the bladesCutting unit rear ejection Bio MAINTENANCELubrication Rider 11 and Rider 11 Bio Changing the oilLubrication of front wheel bearings Check that the lock-ring is correctly posi- tioned in the slotGeneral lubrication Lubrication of belt tensionerMAINTENANCE 32 - EnglishChecking and adjustment of the throttle wire Replacement of the fuel filterMAINTENANCE TROUBLE SHOOTING SCHEDULE ProblemProcedure Service STORAGEWinter storage Dimensions TECHNICAL DATARider Rider 13 HRider 13 H Bio Rider 11 BioTECHNICAL DATA DimensionsDirective 89/392/EEC, Annex II, A EU declaration of conformity Only applies to EuropeSvenska ´*3,¶6X¨ Svenska ´*3,¶6X¨ 2000W37