Husqvarna FS 6600 D, FSA 8400 D manuel dutilisation FS6600 Diesel Specifications

FS6600 DIESEL SPECIFICATIONS

Standard & CE Models

FS6600 Diesel Model			FS6600		FS6600		FS6600	FS6600	FS6600
			18”			26”	30”	36”	42”
FS6600 Diesel Model – CE			FS6600		FS6600		FS6600	FS6600	FS6600
			450mm		650mm		750mm	900mm	1000mm
ALL SAWS FEATURE:
Blade Guard Capacity - in. (mm)			18 (457)	26 (660)			30 (762)	36 (914)	42 (1,067)
Max. Depth of Cut - in. (mm)			6.50 (165)	10.50 (267)			12.50 (318)	15 (381)	20.50 (508)
Blade Shaft RPM			2,400	1,800			1,600	1,350	1,180
Approximate Blade Shaft HP			60 Horsepower
Arbor Size in. (mm)			1" (25.4) with single drive pin
Quick Disconnect Blade Flange			5			5	5	6	7
Diameter – in. (mm)			(127)			(127)	(127)	(152)	(178)
Blade Shaft Diameter - in. (mm)			2" (51)
Blade Shaft Bearings			Cast Sealed blade shaft with 4 maintenance-free ball bearings
Blade Shaft Drive			Dual 8-groove banded 3VX V-belts (16 grooves total)
Blade Coolant			Zinc plated dual multiple-jet water spray tubes
Blade Guard Attachment			Slip-on through 36" (900mm); Bolt-On for 42” (1000mm), auto-latch
Blade Control			Electro-hydraulic pump raises blade; switch controlled raise/lower on speed control handle;
			switch controlled positive depth stop; dial type cutting depth indicator; blade drive
			disengagement system (clutch); quick disconnect blade flanges
Axle		Front	1.25" (31.75 mm) diameter
		Rear	Easy Adjust Center Pivot w/2 Hydraulic Powered Wheel Motors
Wheels		Front	8” x 3" x 1" (203mm x 76mm x 25.4mm)
			Thick polyurethane tread; sealed ball bearing requiring less maintenance
		Rear	10" x 3" x 1.25" (254mm x 76mm x 32mm)
			Solid rubber, Quick disconnect
Transmission			Hydrostatic Pump, w/2 Hydraulic Wheel Motors connected with hoses, neutral start switch,
			single handle speed control, Hydraulic bypass valve for pushing.
Max. Ground Speed			Infinitely variable: 0 – 300 FPM forward & reverse. (25 M/min maximum reverse speed on CE models)
Chassis			Heavy-duty, rigid, box and channel section construction
Weight – lb. (Kg) – Uncrated			1,789 (812)	1,811 (822)			1,832 (831)	1,863 (845)	1,888 (857)
POWER SOURCE:
Engine			John Deere Turbocharged Diesel
Specifications			4024TF270
Max. Horsepower			66 @ 2,800 RPM DIN. (49.2 kW)
Displacement cu. in. (l)			149 cu. in. (2.44 liter)
Bore – in. (mm)			3.39 (86)
Stroke – in. (mm)			4.13 (105)
Cylinders			4
Fuel Capacity – gal. (l)			10 (37.8)
Oil Capacity – qt. (l)			8.5 (8) with filter OR 7.6 (7.2) without filter
Air Filter			Radial Seal with pre-cleaner and restriction indicator
Starter			Electric
Engine Coolant			50/50 Water/Ethyl Glycol Mix
SAW DIMENSIONS w/ 36” (900mm) guard:						Metric
				Inches		(mm)
A	Saw Width			37-3/8		949
B	Center to Center Wheel Width (track) – FRONT			24-5/8		625
	Center to Center Wheel Width (track) – REAR			25-1/4		642
C	Outside to Outside Wheel Width - FRONT			27-5/8		702
	Outside to Outside Wheel Width - REAR			28-1/4		717
D	Frame Width			29-1/2		749
E	Inner Flange to Inner Flange Width			32-1/2		825
F	Handle Extension			30		762
G	Minimum Saw Length (handles in, pointer up,			61		1,550
	guard up)
H	Saw Length (pointer up, handles extended)			84		2,133
I	Maximum Overall Height (pointer up)			53		1,346
	Maximum Overall Height (top of pre-cleaner,			56		1,422
	pointer down)
K	Minimum Overall Height (no muffler, rotate pre-			49-1/2		1,255
	cleaner)
L	Wheel Base			24		610
M	Guard to Handle Length (handles in)			75		1,905
N	Maximum Overall Length (handles in)			106 1/2		2,705
O	Maximum Overall Length (handles extended)			129		3,276

36