Husqvarna FS 6600 D, FSA 8400 D manuel dutilisation 2M. V-BELTS Set, 2N. Gearbox Pulley

FIGURE 3-2
				3-1D3
		3-2D
3-2O				3-2D2
	3-2P			3-2D1
3-2A
3-2C	3-2B
				3-2N
3-2E
				3-2M
	3-2J			3-2K
3-2F	3-2I	3-2H	3-2G	3-2L

3-2A. ENGINE GEARBOX: Three Speed Model.

3-2B. WATER CONNECTION: Circulates freshwater through gearbox to cool it. Water then flows to the bladeguard.

3-2C. WATER DRAIN VALVE: To drain water from gear- box: Turn Counterclockwise to open, Clockwise to close. Drain daily to prevent corrosion or damage due to freezing temperatures.

3-2D. HOOD LATCH: One latch secures hood in lowered position. US Model Operation: 1. Press HOOD LATCH (3-1D3/3-2D3) inward. 2. Raise hood until HOOD SUPPORT (6H) is engaged & sup- ports hood. CE Model Operation: 1. Use tool to loosen Capscrew (3-1D1/3-2D1). 2. Pivot tube latch (3-1D2/3-2D2) downward. 3. Press HOOD LATCH (3-1D3/3-2D3) inward. 4. Raise hood until HOOD SUPPORT (6H) is engaged & supports hood.

3-2E. FLANGE COVER: Guards against FLANGE contact during operation. Always keep in place!

3-2F. BELT PROTECTOR SHIELD: Keep in place.

3-2G. BLADESHAFT TUBE ASSY: Sealed unit contains bladeshaft, bearings and shaft seals.

3-2H. TIEDOWN LUGS: Used to tie the saw down while transporting by vehicle. Not to be used to lift the saw.

3-2I. ENGINE OIL DRAIN VALVE: Drains engine oil without use of tools.

3-2J. BELT TENSIONING BOLTS:

3-2K. HORIZONTAL CLAMPING BOLTS:

3-2L. BLADE SHAFT PULLEY:

3-2M. V-BELTS: Set of 4.

3-2N. GEARBOX PULLEY:

3-2O. GEARBOX SHIFT LEVER: Use to change output speed of the ENGINE GEARBOX (3-2A). Three- Speeds and two Neutral positions are available. GEARBOX SHIFT LEVER positions (1, 2, and 3) are color coded to match, among others, Gearbox Range / Blade RPM decal. GEARBOX SHIFT LEVER Operation:

1)Turn ENGINE START SWITCH (1H) to OFF (“0”) position. Always turn Engine OFF before shifting gearbox!

2)Verify that pulley size, flange size, and blade shaft speed are correct for the blade size being mounted.

WARNING: Serious injury can occur to the operator or people in the work area if the rota- tional speed (n/min) of the DIAMOND BLADE (2E) exceeds the maximum speed (n/min) marked on the DIAMOND BLADE (2E).

3)Lift GEARBOX DETENT KNOB (3-2P) and twist to hold in “OPEN” position.

4)Move GEARBOX SHIFT LEVER (3-2O) to required gear. A slight “rocking motion” of the gearbox output shaft (or BLADE SHAFT) may improve shifting.

5)Twist and lower GEARBOX DETENT KNOB (3-2P) back to original “LOCKED” position.

3-2P. GEARBOX DETENT KNOB: Locks GEARBOX SHIFT LEVER (3-2O) in position. See GEARBOX SHIFT LEVER (3-2O) for operation.

48