Honeywell K5305-1V5 Installation and Setup Guide, The 6150rf is a Medium receiver, zones

Installation and Setup Guide

RELAY

RELAY

4229

CONNECTOR

2

DIP SWITCH

FOR SETTING ADDRESS

EITHER OR BOTH CAN BE USED

TERMINALS ON

AND ZONE "A" RESPONSE

CONTROL PANEL

RELAY

1

TB2

NO C

NC

4-PIN CONSOLE PLUG

4

GRN

DATA OUT (>)

(TERM 6)

TAMPER JUMPER POSITION

TO CONTROL

BLK

4229 IN CABINET

4

3

(–) GROUND

(TERM 4)

WHT

GRY VIO BLK YEL ORG

BRN

(NOT TAMPER)

4229 REMOTE

3

2

RED

(+) 12VDC

(TERM 5)

(TAMPER PROTECTED)

TB1

2

DATA IN (<)

NO NC C GND NO NC C

YEL

1

1

FROM

(TERM 7)

1

2

3

4

5

6

7

8

9

10

11

12

CONTROL

RLY	RLY					TERMINATE EACH
						PROGRAMMED ZONE
2	1	REED
						WITH 1000 OHM (1K)
RELAYS OFF		(TAMPER)				END-OF-LINE RESISTOR
		SWITCH				(EACH ZONE'S MAX.
						LOOP RESISTANCE
		ZONES A B	C D	E F	G H	300 OHMS + EOL)
						4229-002-V0

Figure 10. Wiring Connections, 4219 & 4229 (4229 shown)

Installing the RF Receiver and Wireless Transmitter Zones

	Compatible Receivers	Use any ADEMCO 5800 Series Wireless Receivers, such as:
The 6150rf is a Medium receiver			RF Receiver	No. of Zones
			5881L/5882L	up to 8
only capable of support 16 wireless			5881M/5882M	up to 16
zones			5881H/5882H,	VISTA-20P	= up to 40 plus 16 buttons
			5883, 6150RF	VISTA-15P	= up to 26 plus 8 buttons
	Receiver Connections	1. Set Device Address to “00” (set all switches to the right, “off” position).

2.Mount the receiver, noting that the RF receiver can detect signals from transmitters within a nominal range of 200 feet.

3.Connect the receiver's wire harness to the control's keypad terminals. Plug the connector at the other end of the harness into the receiver. Refer to the installation instructions provided with the receiver for further installation procedures regarding antenna mounting, etc.

WIRELESS ZONE NUMBERS

VISTA-20P: transmitter zones 9-48 button zones 49-64

NOTE

CIRCUIT BOARD IS MOUNTED IN CONTROL'S CABINET. GROUNDING LUGS (2) PROVIDED MUST BE INSERTED IN LEFT-HAND TERMINALS OF ANTENNA BLOCKS AND SECURED TO CABINET. (SEE RECEIVER'S AND CONTROL'S INSTRUCTIONS)

MOUNTING

HOLES

ANTENNAS

(INSERT IN

RIGHT-HAND

TERMINALS)

INSERT IN

RIGHT- HAND

TERMINALS

MODEL NO. IS INDICATED ON CIRCUIT BOARD

5882	DIP
LOCATION	SWITCH

INTERFERENCE

INDICATOR

LED

CIRCUIT BOARD

YELLOW	TO CONTROL'S
RED
	REMOTE KEYPAD
BLACK
	CONNECTION
GREEN	POINTS.

WIRING OPENING

KNOCKOUT AREA

FOR SURFACE WIRING

VISTA-15P: transmitter zones 9-34 button zones 49-56

SOCKET	PLUG
TO RELEASE CIRCUIT BOARD,
REMOVE SCREWS AND
BEND BACK TABS	5881-003-V0

		Figure 11. 5881/5882 RF Receiver (cover removed)
RF Receiver Notes	Set the following options:
	*22	RF Jam Option†
† These fields must be	*24	RF House ID Code (if using wireless keypads) for each partition
enabled for Residential Fire,	*67	Transmitter Low Battery Report Code†
UL Residential Burglar	*75	Transmitter Low battery restore report code†
Alarm, and UL Commercial
	• The receiver is supervised and a trouble report is sent (“CHECK 100” displayed) if
Burglar Alarm installations.
	communication between the panel and receiver is interrupted, or if no valid RF signals
	from at least one supervised transmitter are received within 12 hours.
	If the receiver is mounted remotely:
	• Place the RF receiver in a high, centrally located area for best reception.
	• Do not locate the receiver or transmitters on or near metal objects. This will decrease
	range and/or block transmissions.
	• Do not locate the RF receiver in an area of high RF interference (indicated by frequent
	or prolonged lighting of the LED in the receiver; random flicker is OK).
	• Do not locate RF receiver closer than 10 feet from any keypads to avoid interference
	from the microprocessors in those units.

2-8