Honeywell K5305-1V5 Installation and Setup Guide, Zone Number, Summary Screen, Zone Type ZT

Installation and Setup Guide

Enter Zn Num.
(00 = Quit)	10

Zone Number

VISTA-20P: wired 01-08 (and 09-48†); wireless 09-48; RF button zones 49-64

VISTA-15P: wired 01-06 (and 07-22†); wireless 09-34; RF button zones 49-56

Both Controls: 91 = addr. device report enable; 92 = duress report enable 95, 96, 99 =emerg. zones

[∗] to continue; 00 to quit † if zone expanders are used.

Enter the zone number that you wish to program. Zone 10 has been entered in the example display at left.

Enter a report code for zone 91 to enable addressable device reporting. Enter a report code for zone 92 to enable duress reporting.

95, 96, 99 are emergency (panic) key zones.

				Summary Screen
Zn ZT P RC		In: L
				[∗] to continue
10 00	1 10	RF:	1
				A summary display appears.
OR
				“IN: L” appears for wireless zones and indicates input type and loop.
Zn ZT P RC		In: AD		“IN: AD” appears for hardwire expansion zones (AW) and indicates the module’s address
10 00	1 10	AW: 07		(AD), which is based on the zone number.
OR				“HW: RT” appears for hardwire zones and indicates configuration (EOL, NO, NC, zone
Zn ZT P RC		HW: RT		doubling, double-balanced) and response time selection.
10 00	1 10	EL	1

10 Zone Type

Perimeter 03

Zone Type (ZT)

See table below.

Each zone must be assigned to a zone type, which defines the way in which the system responds to faults in that zone. Enter the Zone Type code from the list below:

Note: If 00 is entered, Delete Zone ? will be displayed.

00	= Not used	07	= 24-Hr Audible	20	= Arm–STAY*
01	= Entry/exit #1	08	= 24-Hr Aux	21	= Arm–AWAY*
02	= Entry/exit #2	09	= Fire	22	= Disarm*
03	= Perimeter	10	= Interior w/Delay	23	= No Alarm Resp
04	= Interior Follower	12 = Monitor Zone		24	= Silent Burglary
05	= Day/Night	14	= Carbon Monoxide	77	= Keyswitch
06	= 24-Hr Silent	16	= Fire w/Verify	81 = AAV Mon. Zone
*5800 button-type transmitters only				90-91 = Configurable

		Partition No. (P) (VISTA-20P)
10 Partition
		1-3 = partition (3 = common); [∗] to continue
	1
		Enter the Partition number for this zone. Partition 1 is shown entered.

	Report Code (RC)
10 Report Code
	First Digit: 1-9, #+10 for 0, #+11 for B, #+12 for C, #+13 for D, #+14 for E, #+15 for F
1st 01 2nd 00 10
	00 to disable
	Second Digit: same as above; [∗] to continue
	Enter the report code for this zone, which consists of 2 hexadecimal digits, each in turn
	consisting of 2 numerical digits. For example, for a report code of “10,” enter 01 and 00.
	For Contact ID®, entering any non-zero entry as the first digit enables the report code for
	this zone. Refer to the System Communication section for information about report codes
	and formats.

		Hardwire Type
02 HARDWIRE TYPE
		0 = EOL; 1 = NC; 2 = NO; 3 = zn doubling (ZD) †; 4 = dble-balanced (DB)†
EOL	0
		[∗] to continue	† VISTA-20P

This prompt appears only for zone numbers 02-08.

Zone 1 is automatically set for EOL operation.

02 Response Time

1

Response Time (RT)

0 = 10mSec; 1 = 350mSec; 2 = 700mSec; 3 = 1.2 seconds; [∗] to continue

This prompt appears only for hard-wired zones 01-08 (zone 02 is the display shown). Option 3: used for “clean me” option on zone 1 (see field ∗174).

NOTE: If zone doubling is being used, the response time selected for zones 02-08 automatically applies to each zone’s associated doubled zone.

5-2