Honeywell K5305-1V5 Installation and Setup Guide, Auxiliary Device Current Draw Worksheet

Installation and Setup Guide

CABINET	A	B
		CABINET
		BOARD
	RECEIVER CIRCUIT BOARD	SUPPORTING
		SLOTS

+	+
	CIRCUIT
	BOARD
	MOUNTING
	CLIP

CONTROL

CIRCUIT

BOARD

	DETAIL A
MOUNTING	SIDE VIEW
CLIP	OF BOARD -

SUPPORTING SLOTS

INSTALLATION WITH RECEIVER CIRCUIT BOARD

WHITE	BLACK	RED
MOUNTING	MOUNTING	MOUNTING
CLIP	CLIP	CLIP

NOTE

A COMBINATION OF THESE MOUNTING CLIPS HAS BEEN INCLUDED IN YOUR INSTALLATION KIT.

USE THE APPROPRIATE CLIPS FOR MOUNTING.

IF NO RF RECEIVER IS USED, MOUNT THE PC BOARD USING EITHER THE WHITE OR BLACK CLIPS, WHICHEVER ARE INCLUDED IN THE CONTROL PANEL'S HARDWARE KIT.

ANTENNA

(2)

SCREW

(2)

GROUNDING LUG

(2)

ANTENNA

MOUNT

(2 PLACES)

DETAIL B

ANTENNA AND GROUNDING

LUG INSTALLATION

pc_mount-001-V1

Figure 3. Mounting the PC Board and RF Receiver

AUXILIARY DEVICE CURRENT DRAW WORKSHEET

	DEVICE	CURRENT	No. UNITS	TOTAL CURRENT
6150	Fixed-Word Keypad	40mA/70mA**
6160	Alpha Keypad	40mA/150mA**
6150V Fixed-Word Display Voice Keypad		60mA/160mA**
6160V Alpha Display Voice Keypad		60mA/190mA**
8132/8142 Series AUI (Symphony)		150mA/400mA**
6270	Touch Screen Keypad	180mA/280mA**
5881/5882 RF Receiver		60mA
5883	Transceiver	80mA
4219 Zone Expander		30mA
4204	Relay Unit	15/180mA‡
4229	Zone Expander/Relay Unit	30/100mA‡
4285 Phone Module		160mA
4286 Phone Module		300mA
*
(Current available from Aux. terminals = 600		mA max.)†	TOTAL =

*If using hardwire devices such as PIRs, refer to the specifications for that particular unit's current draw. ** Values are for standby/alarm; alarm for keypads means armed with backlighting on and sounder on

†In UL installations, maximum current draw from the Auxiliary Output and the Alarm Output combined must not exceed 600 mA (500 mA max from Aux. Output). ‡Values are for relays OFF/relays ON.

CALIFORNIA STATE FIRE MARSHALL (CSFM) AND UL RESIDENTIAL FIRE

24-HOUR BATTERY BACKUP REQUIREMENTS

The California State Fire Marshal and UL have regulations which require that all residential fire alarm control panels must be provided with a backup battery which has sufficient capacity to operate the panel and its attached peripheral devices for 24 hours in the intended standby condition, followed by at least 4 minutes in the intended fire alarm signaling condition. This control panel can meet these requirements without using a supplementary power supply, provided that the panel’s auxiliary power and bell output currents are limited as indicated below.

OUTPUT LIMITATIONS AND CORRESPONDING REQUIRED BATTERIES

OUTPUT CURRENT LIMITATIONS		BATTERY INFORMATION
Output Current Total	Maximum Auxiliary Current	Battery Capacity	Recommended Battery
		To Use (Amp/Hrs)	(Yuasa Model No.)
600mA maximum total of	45mA	4AH	NP4-12 (or ADEMCO 467)
auxiliary power plus bell	160mA	7AH	NP7-12
output currents	200mA	8AH	NP4-12 (two) ‡
	425mA	14AH	NP7-12 (two) ‡
	500mA	17.2AH	NPG18-12

‡ NOTE: Use two batteries, connected in parallel. Obtain an Ademco Battery Harness Kit SA5140-1. (Both batteries will fit inside the cabinet.)

2-2