|
| Programming Overview |
|
|
|
| Type 05 | • Assign to a zone that contains a |
| Trouble by Day/ | covering a sensitive area such as a stock room, drug supply room, etc. |
| Alarm by Night | • Can also be used on a sensor or contact in an area where immediate notification of an entry is |
|
| desired. |
|
| • Provides an instant alarm if faulted when armed in the Away, Stay, |
|
| Maximum (night) modes. |
|
| • During the disarmed state (day), the system will provide a latched trouble sounding from the |
|
| keypad (and a central station report, if desired). |
| Type 06 | • Usually assigned to a zone containing an emergency button. |
|
| • Sends a report to the central station but provides no keypad display or sounding. |
|
|
|
| Type 07 | • Assign to a zone that has an emergency button. |
|
| • Sends a report to the central station, and provides an alarm sound at the keypad, and an |
| Alarm | audible external alarm. |
|
|
|
| Type 08 | • Assign to a zone containing an emergency button, or to a zone containing monitoring devices |
|
| such as water or temperature sensors. |
| Auxiliary Alarm | • Sends a report to the central station and provides an alarm sound at the keypad. (No bell |
|
| output is provided.) |
| Type 09 | • Provides a fire alarm on short circuit and a trouble condition on open circuit. A fire alarm |
| Supervised Fire | produces a pulsing bell output. |
|
| • This zone type is always active and cannot be bypassed. |
|
|
|
| Type 10 | • Provides entry delay (using the programmed entry time), if tripped when the panel is armed in |
| Interior w/Delay | the Away mode. |
|
| • Entry Delay 1 begins whenever sensors in this zone are violated, regardless of whether or not |
|
| an entry/exit delay zone was tripped first. |
|
| • Bypassed when the panel is armed in the Stay or Instant modes; if armed in |
|
| zones assigned to zone list 05 |
|
| |
| Type 12 | • Works as a dynamic monitor of a zone fault/trouble (not alarm). In the case of a short/open, the |
| Monitor Zone | message, |
|
| to the Central Station. The system keypad will display a “check” message indicating the |
|
| appropriate zone (but keypad beeping does not occur). Upon restoral of the zone, the message, |
|
| |
|
| • The “check” message will automatically disappear from the keypad dynamically, when the |
|
| zone restores; a user code + off sequence is not needed to reset the zone. |
|
| • Faults of this zone type are independent of the system, and can exist at the time of arming |
|
| without interference. |
|
| • Since this is a “trouble” zone type, do not use this zone type with relays set to activate upon |
|
| “alarm.” |
| Type 14 | • Assigned to any zone with a carbon monoxide detector. |
| 24 Hour Carbon | • The bell output will pulse when this zone type is alarmed. |
| Monoxide | • Always active and cannot be bypassed. |
| Monitor |
|
| Type 16 | • Provides a fire alarm when zone is shorted, but only after alarm verified. |
| Fire | • System verifies alarm by resetting zones for 12 seconds after short is detected. A subsequent |
| w/Verification | short circuit within 90 seconds triggers fire alarm. |
|
| • Provides a trouble response when zone is open. |
| Type 20 | • Arms the system in Stay mode when the zone is activated. |
|
| • Pushbutton units send the user number to the central station when arming or disarming. |
| only) | • User number for button must be assigned. |
|
|
|
| Type 21 | • Arms the system in Away mode when the zone is activated. |
|
| • Pushbutton units send the user number to the central station when arming or disarming. |
| only) | • User number for button must be assigned. |
|
|
|
| Type 22 | • Disarms the system when the zone is activated. |
| Disarm (BR only) | • User number for button must be assigned. |
|
|
|
