Honeywell VISTA 20P, VISTA-20PSIA, VISTA-15P, VISTA-15PSIA Various System Trouble Displays

		System Operation
Various System Trouble Displays
Alpha Display	Fixed Disp.	Meaning
ALARM CANCELED	CA	will appear if an exit or interior zone contained a fault during closing at the
		time the Exit Delay ended (e.g., exit door left open), but the system was
		disarmed during the Entry Delay time. The alarm sounder and keypad sound
		continuously, but stop when the system is disarmed. No message will be
		transmitted to the central station.
EXIT ALARM	EA	appears when Exit Delay ends if an exit or interior zone contained a fault
		during closing. The alarm sounder and keypad sound continuously until the
		system is disarmed (or timeout occurs). An “Exit Alarm” message is sent to the
		central station. Also results if an alarm from an exit or interior zone occurs
		within 2 minutes after the end of an Exit Delay.
CHECK	CHECK	indicates that a problem exists with the displayed zone(s) and requires
		attention.
ALARM 1xx	1xx	indicates that communication between control and a zone expander or wireless
FAULT 1xx	1xx	receiver is interrupted, where “xx” is the device address. Check the wiring and
CHECK 1xx	1xx	DIP switch settings on the units.
	91	If field *199 is set to “1,” all ECP module problems are displayed as “91.”
		If there are wireless sensors in the system, the Check condition may also be
		caused by some change in the environment that prevents the receiver from
		receiving signals from a particular sensor.
SYSTEM LO BAT	BAT	with no zone number indicates that the system's standby battery is weak.
LO BAT	BAT	with a zone number and a once-per-minute beeping at the keypad indicates
		that a low-battery condition exists in the wireless sensor displayed (zone “00”
		indicates a wireless keypad). If the battery is not replaced within 30 days, a
		“CHECK” display may occur.
		NOTE: Some wireless sensors contain a non-replaceable long-life battery which
		requires replacement of the entire unit at the end of battery life (e.g., Nos.
		5802, 5802CP).
TELCO FAULT	94	Telephone Line Failure, indicates that a monitored telephone line (if
		programmed in field *92) has been cut or disconnected. Depending on how the
		system was programmed, the keypad may also produce a trouble sound, and
		the external sounder may be activated. Silence by entering installer code +
		OFF.
Busy-Standby	dl	If this remains displayed for more than 1 minute, the system is disabled.
Mode m Comm	CC	The system is in communication with the central station for change of function
		or status verification.
no display	no display	Power Failure
		If there is no keypad display at all and the LEDs are unlit, operating power
		(AC and battery) for the system has stopped and the system is inoperative.
		If the message “AC LOSS” (Alpha display keypads) or “NO AC” (Fixed-Word
		display keypads) is displayed, the keypad is operating on battery power only.
		If the battery standby capacity is used up during a prolonged AC power outage,
		the control's power will shut down to minimize deep discharge of the battery.
Comm. Failure	FC	A communication failure has occurred.
Open Circuit	OC	The keypad is not receiving signals from the control; sees an open circuit.
Long Rng Trbl	bF	Backup LRR communication failure.
Bell Failure	70	Bell supervision failure.
RCVR Jam	90	RF jam detected.
KEYPAD LOW BAT	00 BAT	Wireless keypad low battery.
Phone Okay	Cd	The dialer test has been successful (CID code 601).
Dialer Off	dO	The dialer is disabled.
Test in Progress	dd	Walk test mode is active(CID code 607).
Upload Completed	dC	The upload or download session was completed.
Upload Failed	dF	The upload or download session failed before completion.

6-7