•Rotate the BLADE DEPTH INDICATOR (1Q) needle to align to the “0” depth.

•As DIAMOND BLADE (2E) is lowered into the cutting surface, the current cutting depth will now be indicated by the Orange text number range on BLADE DEPTH INDICATOR (1Q) needle.

SMD or “Set Maximum Depth” Mode without BLADE DEPTH STOP (White colored numbers show uncut depth):

•Turn ENGINE START SWITCH (1H) to “0” (OFF) position to STOP engine (If running).

•Turn ENGINE START SWITCH (1H) to “1” (RUN) position to power electrical system.

•Lower DIAMOND BLADE (2E) by pushing TOGGLE SWITCH (1P) on the SPEED CONTROL LEVER (1O) downward until DIAMOND BLADE (2E) touches the surface to be cut.

•Rotate the BLADE DEPTH INDICATOR (1Q) needle to align with the desired maximum cutting depth on White colored number range. The uncut depth will now be indicated on the White colored number range. When the BLADE DEPTH INDICATOR (1Q) needle gets to the “0” position, the saw is cutting at the desired maximum cutting depth.

•Raise the blade by pushing the TOGGLE SWITCH (1P) on the SPEED CONTROL LEVER (1O) upward until the DIAMOND BLADE (2E) is off of the cutting surface.

•Turn the ENGINE START SWITCH (1H) to the “0” (OFF) position to turn off power to electrical system.

SMD or “Set Maximum Depth” Mode using BLADE DEPTH STOP SWITCH (1M) (White colored numbers show uncut depth):

•Turn ENGINE START SWITCH (1H) to “0” (OFF) position to STOP engine (If running).

•Set the BLADE DEPTH STOP SWITCH (1M) to the “0” (OFF) position to override the depth stop setting. Saw will raise and lower over its full range without stopping.

•Turn ENGINE START SWITCH (1H) to “1” (RUN) position to power electrical system.

•Lower DIAMOND BLADE (2E) by pushing TOGGLE SWITCH (1P) on the SPEED CONTROL LEVER (1O) downward until DIAMOND BLADE (2E) touches the surface to be cut.

•Rotate the BLADE DEPTH INDICATOR (1Q) needle to align with the desired maximum cutting depth on White colored number range.

•Set the BLADE DEPTH STOP SWITCH (1M) to “1” (ON) position.

•Raise the blade by pushing the TOGGLE SWITCH (1P) on the SPEED CONTROL LEVER (1O) upward until the DIAMOND BLADE (2E) is off of the cutting surface.

•Turn the ENGINE START SWITCH (1H) to the “0” (OFF) position to turn off power to electrical system.

•Now the maximum cutting depth is set. If the saw is raised out of the cut surface for any reason it can now be lowered to “Set Max. Depth” by lowering the blade until the saw lowering movement stops.

The saw WILL NOT lower to any depth greater than the position set on the BLADE DEPTH STOP SWITCH (1Q). If a deeper cut is required, the BLADE DEPTH INDICATOR (1Q) MUST be turned to the new depth position. Or push the BLADE DEPTH STOP SWITCH (1M) to “0” (OFF) position to override the Depth Stop Feature.

7 Stopping The Saw

(See Figures 1-2)

For EMERGENCY STOP, press down the RED PALM SWITCH (1K) on the cowl. This will stop the engine and disconnect power to all electrical items except lights. Reset the RED PALM SWITCH (1K) by pulling out until it pops up, then restart engine.

•Move the Control Lever (1O) to the STOP (1BB) position.

•Raise the Diamond Blade (2E) out of the cut by pressing the Raise/Lower Switch (1P) on the Control Lever (1O) upward until the Diamond Blade (2E) clears the surface.

•Disengage the Blade Clutch Switch (1V) if equipped with clutch.

•Turn the Engine Throttle (1F) to the LOW IDLE position.

•Turn off the Water Valve (1T).

•Let the Engine run at idle for a few minutes before shutting off.

•STOP the engine by turning the Engine Start Switch (1H) to the “0” (OFF) position.

8 Incidents During Sawing

(See Figures 1-2)

If ENGINE STOPS during sawing, check the following:

•Engine out of fuel—Check Fuel Gauge (1X).

•Lack of water signals the Water Safety Switch (1L) to stop the engine. Set Switch (1L) to “0” (OFF) and then restart the engine.

•Excessively fast cutting speed will stall engine.

•Red Palm Emergency Switch (1K) has been pressed down. Reset by pulling toggle switch until it pops upward.

•Circuit Breaker is blown (1Z). Push to Reset

If the Diamond Blade (2E) STOPS during sawing, check:

•Drive belt tension is inadequate.

•The clutch switch has been pushed to “0” OFF

•The clutch has an electrical failure or blown fuse.

54

Page 53 Page 55
Page 54
Image 54
Husqvarna FS 6600 D, FSA 8400 D manuel dutilisation Stopping The Saw, Incidents During Sawing, See Figures
Page 53 Page 55

FSA 8400 D, FS 6600 D specifications

Husqvarna has long been a trusted name in the world of professional outdoor power equipment, and its FS 6600 D and FSA 8400 D models exemplify the company's commitment to quality and performance.

The Husqvarna FS 6600 D is a powerful walk-behind concrete saw that is renowned for its exceptional cutting efficiency and robust design. Powered by a high-torque diesel engine, the FS 6600 D is engineered to handle tough, heavy-duty applications with ease. One of its standout features is its adjustable, heavy-duty frame that can accommodate various blade sizes, making it versatile for different cutting depths and applications. The saw's integrated water system helps to manage dust and keeps the blade cool during operation, resulting in cleaner cuts and prolonging blade life. Furthermore, the intelligent design of the FS 6600 D includes an easy-to-use control panel, ensuring operators can quickly start and adjust the saw without hassle.

On the other hand, the Husqvarna FSA 8400 D is part of Husqvarna’s range of professional grass trimmers, specifically designed for demanding tasks and prolonged use. Its lightweight yet robust design makes it an ideal choice for professionals who require mobility and efficiency. The FSA 8400 D features a high-capacity battery and an efficient brushless motor, ensuring powerful performance with minimal noise and vibration. The trimmer’s adjustable handle and ergonomic design allow users to maneuver easily, reducing fatigue during extended usage.

Both products also incorporate advanced technologies to enhance user experience. For instance, the FS 6600 D employs Husqvarna’s SmartStart technology, allowing for easier and faster starts. Similarly, the FSA 8400 D utilizes an intuitive control system that seamlessly integrates speed and power settings, optimizing performance based on the demands of the task at hand.

In summary, the Husqvarna FS 6600 D and FSA 8400 D are prime examples of innovative engineering combined with user-focused design. Their robust features, advanced technologies, and unmatched performance make them essential tools for professionals looking to excel in their trade. Whether cutting concrete or tidying up grassy areas, Husqvarna proves that it understands the needs of its users, delivering reliable solutions that stand the test of time.
Top Page Image Contents