Integra DPS-6.7 Rear Panel, Audio Output 20, 22, Jack, Ir In/Out, Surr Mode switch

DPS-6.7_En.book Page 15 Monday, July 31, 2006 3:12 PM

Front & Rear Panels—Continued

Rear Panel

1 2 3 4 5 6 7 8 9 J

K L M

AAUDIO OUTPUT [20, 22, 23]

These jacks make up the multichannel analog audio output. The FRONT/D.MIX jacks can be connected to a stereo input on a TV, hi-fi amp, or other compo- nent. The 1 and 2 jacks output the same signals, so use either pair. If you use this connection, in the Speaker Configuration (page 48), set the Sub- woofer, Center Speaker, and Surround Speaker set- tings to Off, so that 5.1-channel DVD audio is down mixed into two channels.

If you’re using an AV receiver or surround decoder with a 5.1-channel analog audio input, use the FRONT/D.MIX 1 or 2 jacks and the SURR 1 L/R, CENTER, and SUBWOOFER jacks.

If you’re using an AV receiver or surround decoder with a 7.1-channel analog audio input, connect the SURR 2 L/R jacks to your amp’s surround back L/R jacks, and set the SURR MODE switch to “1+2.” The SURR 1 and SURR 2 jacks output the same signals.

B jack [23]

These (Remote Interactive) connectors can be

connected to the connectors on your other Inte- gra/Onkyo AV components for interactive control.

Connecting an cable only does not make the system operational. You must also connect the audio cables as well.

CRS 232

This port is for servicing.

DIR IN/OUT [25]

A commercially available IR receiver can be con- nected to the IR IN jack, allowing you to control the DVD player when it's out of sight, for example, installed in a cabinet.

A commercially available IR emitter can be con- nected to the IR OUT jack to pass IR (infrared) remote control signals along to other components.

EVIDEO OUTPUT 1/2 [20]

FCOMPONENT 1 VIDEO OUTPUT [21]

These jacks output component video and can be connected to an component video input on a TV or projector.

The DVD player has two component video outputs, the COMPONENT 1 and COMPONENT 2, how- ever, they output the same video signal.

GCOMPONENT 2 VIDEO OUTPUT [21]

These BNC connectors can be used to connect a TV or projector with BNC component video inputs. The DVD player has two component video outputs, the COMPONENT 1 and COMPONENT 2, how- ever, they output the same video signal.

HOPTICAL DIGITAL AUDIO OUTPUT [22]

This optical digital audio output can be connected to an optical digital audio input on a hi-fi amp, AV receiver, or surround sound decoder (Dolby Digital, DTS).

ICOAXIAL DIGITAL AUDIO OUTPUT [22]

This coaxial digital audio output can be connected to a coaxial digital audio input on a hi-fi amp, AV receiver, or surround sound decoder (Dolby Digital, DTS).

JAC INLET [26]

The supplied power cord is connected here. The other of the power cord should be connected to a suitable wall outlet.

KSURR MODE switch [23]

This switch is used to turn the AUDIO OUTPUT SURR 2 on or off. To use this output, set the switch to “1+2.” The SURR 2 jacks output the same signals as the SURR 1 jacks.

LHDMI OUT [24]

This HDMI output can be used to connect a TV or projector with an HDMI input. This HDMI connec- tor outputs digital audio and digital video.

MS VIDEO OUTPUT 1/2 [21]

These RCA/phono connectors can be used to con- nect TVs or projectors with composite video inputs. The DVD player has two composite video output connectors. They output the same video signal respectively.

These connectors can be used to connect TVs or projectors with S-Video inputs.

The DVD player has two S-Video output connec- tors. They output the same video signal.

15