Integra DTR-8.8 Recording the Input Source, Recording from Different AV Sources

Recording

This section explains how to record the input source and how to record audio and video from separate sources.

Notes:

•The surround sound and DSP listening modes cannot be recorded.

•Copy-protected DVDs cannot be recorded.

•Sources connected to the analog multichannel input cannot be recorded.

•Various restrictions apply to digital recording. Refer to the manuals supplied with your digital recording equipment for more details.

•Digital input signals are output by only the digital out- puts, and analog input signals are output by only the analog outputs. There is no internal conversion from digital to analog or vice versa.

•DTS signals will be recorded as noise, so don’t attempt analog recording of DTS CDs or LDs.

Recording the Input Source

Audio sources can be recorded to a recorder (e.g., cas- sette deck, CDR, MD) connected to the TAPE OUT or DIGITAL OPTICAL OUT jacks. Video sources can be recorded to a video recorder (e.g., VCR, DVR) con- nected to the VCR/DVR OUT jacks. See pages 29 to 45 for hookup information.

1	Use the input selector buttons to
	select the source that you want
	to record.

See “Which Connections Should I Use?” on page 30 to see which signals can be output and recorded.

You can watch the source while record- ing it. The AV receiver’s Master Vol- ume control has no effect on recording.

Remote

controller

DVD	VCR/DVR	CBL/SAT
1	2	3
Game/TV	AUX 1	AUX 2
4	5	6
Tape	Tuner	CD
7	8	9
Phono	Net/USB
+10	0

2	On your recorder, start record-
	ing.
3	On the source component, start
	playback.

Note:

•If you select a different input source during recording, that input source will be recorded instead.

Recording from Different AV Sources

You can overdub audio onto your video recordings by simultaneously recording audio and video from two sep- arate sources. This is possible because only the audio source is switched when an audio-only input source, such as TAPE, TUNER, or CD, is selected, the video source remains the same.

In the following example, audio from the CD player con- nected to the CD IN and video from the camcorder con- nected to the AUX 2 INPUT VIDEO jack are recorded by the VCR connected to the VCR/DVR OUT jacks.

Camcorder

video signal audio signal

HDMI

ASSIGNABLE

RS232	IN 4	IN 3	IN 2	IN 1	OUT	OUT
					MAIN	SUB

				ANTENNA
COMPONENT VIDEO ASSIGNABLE			AM		FM75
IN 3	IN 2 IN 1(DVD)	MONITOR
		OUT

Y

AUX 1

GAME/TV

CBL/SAT

VCR/DVR

DVD

MONITOR

IR

OUT

V

IN

REMOTE CB/PB

V

ZONE 2

CONTROL

OUT

DIGITAL ASSIGNABLE

COAXIAL

IN 1

(DVD)

CR/PR

S

S

OUT

IN

IN

OUT

IN

IN

IN

IN

OUT

IN

IN

FRONT

CENTER

SURR

SURR BACK

IN 2

(VCR/DVR)

L

L

IN 3

(CBL/SAT)

R

R

OPTICAL

IN 1

PHONO

CD

TAPE

AUX 1

GAME/TV

CBL/SAT

VCR/DVR

DVD

SUBWOOFER

MULTI CH

(GAME/TV)

GND	ZONE2 R	SURR BACK R	FRONT R	SURR R	CENTER	SURR L
		Bi-AMP
IN 2
(CD)
OUT
		FRONT R (BTL)

CD player VCR

1	Prepare the camcorder and CD player for
	playback.
2	Prepare the VCR for recording.
3	Press the [AUX 2] input selector button.
4	Press the [CD] input selector button.

This selects the CD player as the audio source but leaves the camcorder as the video source.

5 Start recording on the VCR, then start playback on the camcorder and CD player.

Video from the camcorder and audio from the CD player are recorded by the VCR.

95