Integra DTR-8.8 instruction manual 135, Learning Commands, Steps 2, Press the button you want to

Controlling Other Components—Continued

Learning Commands

The AV receiver’s remote controller can learn the com- mands of other remote controllers. By transmitting, for example, the Play command from your CD player’s remote controller, the remote controller can learn it, and then transmit the exact same command when its Play

[ ] button is pressed in the CD remote mode. This is useful when you’ve entered the appropriate remote control code (page 132) but some buttons don’t work as expected.

							Remote
							indicator
1	On	Standby				TV
							Input
	DVD	VCR/DVR			CBL/SAT
	1			2	3		+
	Game/TV		AUX 1		AUX 2		TV CH
	4			5	6		-
	Tape		Tuner		CD
	7			8	9
	Phono	Net/USB			D.TUN		TV VOL
	+10			0	Clear
	--/--- 10			11		12
	Input Selector
		Macro
	1			2	3		Zone3
1, 4			Remote Mode
	DVD		VCR		CD		Zone2
				CDR/MD/Dock
	TV	Cable			Net/USB		Receiver
			SAT				Tape/AMP
	Dimmer						Sleep
				nu	Me
				Me
			p		n
		o				u
		T
	+
	CH			Enter			VOL
	Disc
	Album
	-			G
					it
	Prev			uide	Ex
		S				rn
	CH		e	tup	u
					Ret
	Display						Muting

3

Point the remote controllers at

each other, about 2 to 6 inches

(5–15 cm) apart, and then press

and hold the button whose com-

mand you want to learn until the

Remote indicator flashes.

If the command is learned successfully,

the Remote indicator flashes twice.

R

VOLUME

MUTING

TESTTONE

VEL

SEL

CH

PRESET

D

C

DVD

TAPE

INPUT

TUNER

CH-

PHONO

About 2 to 6

MULTI

GROUP

R

CTOR

SELETUNER

MODESU

DIMM

2-

VIDEO

1-

D

C

DISC

INPUT TAPE

ER

inches (5–15 cm)

SLEEP

DVD

VIDEO

POWER

On

D

Sta

1

VD

G

nd

ane/T

D

by

T

4

V

CR/

ap

2

DV

Phono

7

e

5 AUX1

R

I

--/

+

Tu

C

T

10

BL/S

V

---

10

0Net/USB

8

ner

C

6

A

3 AT

1

2

Input

UX

DVD

Input

9

D

T

+

11

D.

VC

2MacroSelector

Clear

TUN

-

H

R

VV

VCR emote

12

T

SATCable

M

3

OL

ode

Net/USBCDR/MD/Dock

Zone2

Zone3

RC-688M

Sleep

P

Receiver

Tape/AM

4

To learn more commands, repeat

steps 2 and 3.

Press any Remote Mode button when

you’ve finished.

Notes:

• The following buttons cannot learn new commands:

Remote Mode, Macro [1], [2], [3], TV [Input], TV CH

[+]/[–], TV VOL [

]/[

], [D.TUN], Light.

•	The remote controller can learn approximately 70 to
	90 commands, although this will be less if commands
	that use a lot of memory are learned.
•	Remote controller buttons such as Play, Stop, Pause,
	and so on are preprogrammed with commands for

1

Remote Mode

DVD VCR

CD TV

CDR/MD/Dock

Cable Net/USB

SAT

Receiver

Tape/AMP

While holding down the Remote Mode button for the mode in which you want to use the com- mand, press the [On] button.

The Remote indicator lights up.

controlling Integra/Onkyo CD players, cassette decks,

and DVD players. However, they can learn new com-

mands, and you can restore the preprogrammed com-

mands at any time by resetting the remote controller

(see page 133).

• To overwrite a previously learned command, repeat

this procedure.

• Only commands from infrared remote controllers can

be learned.

On

2	Press the button you want to
	learn the new command.

• When the remote controller’s batteries expire, all

learned commands will be lost and will have to be

learned all over again, so don’t discard your other

remote controllers.

135