Manuals / Intel / Computer Equipment / Tablet

Intel FPC 5084, N270 user manual Signal Name, Pin #, RS-422, RS-485, Hardware Installation

Models: N270 FPC 5084

1 73

Download 73 pages 24.28 Kb

Page 20

Signal Name

FPC 5084

When COM1 is set to RS-422 or RS-485, the pin assignments are listed below:

		Signal Name
	Pin #	Signal Name
	Pin #	RS-422	RS-485
		RS-422	RS-485
	1	TX-	DATA-
	2	TX+	DATA+
	3	RX+	No connector
	4	RX-	No connector
	5	No connector	No connector
	6	No connector	No connector
	7	No connector	No connector
	8	No connector	No connector
	9	GND	GND

12	Hardware Installation

Image 20

Intel FPC 5084, N270 user manual Signal Name, Pin #, RS-422, RS-485, Hardware Installation

Contents

All-in-One 8.4” SVGA TFT Fanless Touch Panel Computer with Intel AtomTM N270 Processor Onboard User’s ManualJuly 2009, Version A1 Printed in Taiwan DisclaimersCopyright 2009 Acnodes CorporationAll Rights Reserved Safety Approvals FCC ComplianceSafety Precautions Trademarks Acknowledgments Table of Contents CHAPTER 2 HARDWARE INSTALLATIONCHAPTER 3 AMI BIOS SETUP UTILITY CHAPTER 1 INTRODUCTIONCHAPTER 4 DRIVERS INSTALLATION MEMO General Description Specification Dimensions I/O Outlets Package List CHAPTER INTRODUCTION1.1 General Description Reliable and Stable Design1.2 Specifications BIOS1.2.1 Main CPU Board Embedded O.S. Supported1.2.3 System Specification 8.4” TFT LCD Heat Dispensing Design Net WeightDimension Main Body Size 1.2.2 I/O SystemNOTE All specifications and images are subject to change without notice 1.3 Dimensions This diagram shows you dimensions and outlines of the FPC 5084Introduction 1.4 I/O Outlets Function1.5 Packing List Desktop Stand Kit optional VESA ARM optional Power Adapter optionalFPC 5084 x 1 Panel Mount Kit x Driver CD Wall-Mount Kit IntroductionCHAPTER HARDWARE INSTALLATION 2.1 CF card InstallationWireless LAN Card CompactFlash Card Serial Port Ethernet Mounting Way DramHardware Installation Step 2 Find out the cover on the side of the system2.2 Serial Ports Interface Signal Name Hardware InstallationPin # RS-4222.3 Ethernet 2.4 Mountings - Panel/Wall/Desktop/VESA 2.4.1 Panel Mounting2.4.2 Wall-Mounting Find out the screws as marked on the back side of chassisStep 1 Find out the screws as marked on the back side of chassis 2.4.3 Desktop-MountingHardware Installation Step 2 Assemble the desktop stand to the chassis, and fix the screws Hardware InstallationFPC 5084 User Manual Step 1 Find out the screws as marked on the back side of chassis 2.4.4 VESA-ARM MountingHardware Installation FPC 5084 User Manual Step 3 VESA mounting Installation completedHardware Installation Hardware Installation 2. Find the SO-DIMM socket on mainboard SBC87830 2.5 DRAM Installation1. Unscrew six screws to remove the rear chassis Hardware Installation 3. Push down latches on each side of the SO-DIMM socket2.6 Wireless LAN Card Installation 3. Find the built-in Antenna cable which is tied with other cables on the top of the device. Connect antenna cable to MAIN connector on wireless LAN card FPC 5084 User Manual Hardware InstallationMEMO Page 3.2 Navigation Keys CHAPTER AMI BIOS SETUP UTILITY3.1 Starting 3.3 Main Menu System Time/Date3.4 Advanced Menu Configure advanced CPU settings Execute-Disable Bit CapabilityMax CPUID Value Limit Hyper Threading TechnologyEnhanced C-States IDE ConfigurationSuperIO Configuration Serial Port1 Address Serial Port1 IRQSerial Port2 Address Serial Port2 IRQThis item specifies the IRQ used by the serial port Serial Port4 AddressSerial Port4 IRQ These items display the temperature of CPU and System, Vcore, etc Hardware Health ConfigurationSystem Temperature/CPU Temperature ACPI Settings APM Configuration Power Management/APMVideo Power Down Mode EnabledHard Disk Drive Power Down Mode Power Button ModeSuspend Time Out Minute Throttle Slow Clock RatioResume On RTC Alarm Advanced Resume Event Controls Resume On RingMPS Configuration MPS RevisionPCI Express Configuration Active State Power-ManagementSB PCIE Ports Configuration USB Configuration BIOS EHCI Hand-OffLegacy USB Support USB 2.0 Controller Mode3.5 PCI PnP Menu PCI Latency Timer Clear NVRAMPlug & Play O/S Allocate IRQ to PCI VGAPalette Snooping PCI IDE BusMasterOffBoard PCI/ISA IDE Card IRQ3/4/5/7/9/10/11/14/153.6 Boot Menu Boot Settings Configuration Boot Device Priority Removable DrivesBoot Settings Configuration Quick Boot Quiet BootBoot Num-Lock AddOn ROM Display ModeHit ‘DEL’ Message Display Wait For ‘F1’ If ErrorBoot Device Priority Removable Drives Lan Boot Settings Configuration Supervisor Password User PasswordChange Supervisor Password Change User PasswordBoot Sector Virus Protection menu. You can use the sub menu to change the user passwordDisabled Enabled3.8 Chipset Menu North Bridge Configuration South Bridge ConfigurationNorth Bridge Configuration DRAM Frequency Configure DRAM Timing by SPDBoot Graphic Adapter Priority Video Function ConfigurationAMI BIOS Setup Utility FPC 5084 User ManualSouth Bridge Configuration AMI BIOS Setup UtilityRestore on AC Power Loss PCIE Port ConfigurationUSB Function USB 2.0 Controller3.9 Exit Menu Save Changes and ExitDiscard Changes and Exit Discard ChangesLoad Optimal Defaults Load Fail-Safe DefaultsInstallation of Drivers CHAPTER DRIVERS INSTALLATION4.1 System 4.2 Touch Screen 4.2.1 Specification4.2.2 Driver Installation- Windows XP Installation of Drivers Installation of Drivers FPC 5084 User Manual4. Select the “Standard Calibrate” tab 5. Calibration 6. Press OKPenMount Touch screen 4.3 Embedded O.S4.3.1 Windows XP Embedded 4.3.2 Windows CE.NET Calibration Touch screen