Manuals / Intel / Computer Equipment / Tablet

Intel FPC 5084, N270 user manual Lan Boot Settings Configuration

Models: N270 FPC 5084

1 73

Download 73 pages 24.28 Kb

Page 58

Image 58

FPC 5084

Lan Boot Settings Configuration

The Lan Boot Settings Configuration can enable or disable Lan Boot ROM to allow the system boot on LAN.

48	AMI BIOS Setup Utility

Page 58

Image 58

Intel FPC 5084, N270 user manual Lan Boot Settings Configuration

Contents

All-in-One 8.4” SVGA TFT Fanless Touch Panel Computer with Intel AtomTM N270 Processor Onboard User’s ManualCopyright 2009 Acnodes CorporationAll Rights Reserved DisclaimersJuly 2009, Version A1 Printed in Taiwan Safety Approvals FCC ComplianceSafety Precautions Trademarks Acknowledgments CHAPTER 3 AMI BIOS SETUP UTILITY Table of ContentsCHAPTER 2 HARDWARE INSTALLATION CHAPTER 1 INTRODUCTIONCHAPTER 4 DRIVERS INSTALLATION MEMO 1.1 General Description General Description Specification Dimensions I/O Outlets Package ListCHAPTER INTRODUCTION Reliable and Stable Design1.2.1 Main CPU Board 1.2 SpecificationsBIOS Embedded O.S. SupportedDimension Main Body Size 1.2.3 System Specification8.4” TFT LCD Heat Dispensing Design Net Weight Operation TemperatureNOTE All specifications and images are subject to change without notice 1.3 Dimensions This diagram shows you dimensions and outlines of the FPC 5084Introduction 1.4 I/O Outlets FunctionFPC 5084 x 1 Panel Mount Kit x Driver CD Wall-Mount Kit 1.5 Packing ListDesktop Stand Kit optional VESA ARM optional Power Adapter optional IntroductionWireless LAN Card CHAPTER HARDWARE INSTALLATION2.1 CF card Installation CompactFlash Card Serial Port Ethernet Mounting Way DramHardware Installation Step 2 Find out the cover on the side of the system2.2 Serial Ports Interface Pin # Signal NameHardware Installation RS-4222.3 Ethernet 2.4 Mountings - Panel/Wall/Desktop/VESA 2.4.1 Panel Mounting2.4.2 Wall-Mounting Find out the screws as marked on the back side of chassisHardware Installation 2.4.3 Desktop-MountingStep 1 Find out the screws as marked on the back side of chassis FPC 5084 User Manual Hardware InstallationStep 2 Assemble the desktop stand to the chassis, and fix the screws Hardware Installation 2.4.4 VESA-ARM MountingStep 1 Find out the screws as marked on the back side of chassis Hardware Installation Step 3 VESA mounting Installation completedFPC 5084 User Manual Hardware Installation 1. Unscrew six screws to remove the rear chassis 2.5 DRAM Installation2. Find the SO-DIMM socket on mainboard SBC87830 Hardware Installation 3. Push down latches on each side of the SO-DIMM socket2.6 Wireless LAN Card Installation 3. Find the built-in Antenna cable which is tied with other cables on the top of the device. Connect antenna cable to MAIN connector on wireless LAN card MEMO Hardware InstallationFPC 5084 User Manual Page 3.1 Starting CHAPTER AMI BIOS SETUP UTILITY3.2 Navigation Keys 3.3 Main Menu System Time/Date3.4 Advanced Menu Max CPUID Value Limit Configure advanced CPU settingsExecute-Disable Bit Capability Hyper Threading TechnologySuperIO Configuration IDE ConfigurationEnhanced C-States Serial Port2 Address Serial Port1 AddressSerial Port1 IRQ Serial Port2 IRQSerial Port4 IRQ Serial Port4 AddressThis item specifies the IRQ used by the serial port System Temperature/CPU Temperature Hardware Health ConfigurationThese items display the temperature of CPU and System, Vcore, etc ACPI Settings Video Power Down Mode APM ConfigurationPower Management/APM EnabledSuspend Time Out Minute Hard Disk Drive Power Down ModePower Button Mode Throttle Slow Clock RatioResume On RTC Alarm Advanced Resume Event Controls Resume On RingMPS Configuration MPS RevisionPCI Express Configuration Active State Power-ManagementSB PCIE Ports Configuration Legacy USB Support USB ConfigurationBIOS EHCI Hand-Off USB 2.0 Controller Mode3.5 PCI PnP Menu Plug & Play O/S PCI Latency TimerClear NVRAM Allocate IRQ to PCI VGAOffBoard PCI/ISA IDE Card Palette SnoopingPCI IDE BusMaster IRQ3/4/5/7/9/10/11/14/153.6 Boot Menu Boot Settings Configuration Boot Device Priority Removable DrivesBoot Num-Lock Boot Settings Configuration Quick BootQuiet Boot AddOn ROM Display ModeBoot Device Priority Wait For ‘F1’ If ErrorHit ‘DEL’ Message Display Removable Drives Lan Boot Settings Configuration Change Supervisor Password Supervisor PasswordUser Password Change User PasswordDisabled Boot Sector Virus Protectionmenu. You can use the sub menu to change the user password Enabled3.8 Chipset Menu North Bridge Configuration South Bridge ConfigurationBoot Graphic Adapter Priority North Bridge Configuration DRAM FrequencyConfigure DRAM Timing by SPD Video Function ConfigurationAMI BIOS Setup Utility FPC 5084 User ManualSouth Bridge Configuration AMI BIOS Setup UtilityUSB Function Restore on AC Power LossPCIE Port Configuration USB 2.0 ControllerDiscard Changes and Exit 3.9 Exit MenuSave Changes and Exit Discard ChangesLoad Optimal Defaults Load Fail-Safe Defaults4.1 System CHAPTER DRIVERS INSTALLATIONInstallation of Drivers 4.2.2 Driver Installation- Windows XP 4.2.1 Specification4.2 Touch Screen Installation of Drivers 4. Select the “Standard Calibrate” tab 5. Calibration Installation of DriversFPC 5084 User Manual 6. Press OK4.3.1 Windows XP Embedded 4.3 Embedded O.SPenMount Touch screen 4.3.2 Windows CE.NET Calibration Touch screen

￿Lan Boot Settings Configuration

Lan Boot Settings Configuration