Manuals / Intel / Computer Equipment / Tablet

Intel N270 USB Function, USB 2.0 Controller, Audio Controller, SLPS4# Min. Assertion Width

Models: N270 FPC 5084

1 73

Download 73 pages 24.28 Kb

Page 65

USB Function

FPC 5084 User Manual

(2)

USB Function

This item allows you to enable or disable USB function.

USB 2.0 Controller

This item allows you to enable or disable the USB 2.0 controller.

Audio Controller

This item allows you to enable or disable the audio support.

SLP_S4# Min. Assertion Width

This item allows you to set the SLP_S4# Assertion Width.

Restore on AC Power Loss

This item can control how the PC will behave once power is restored following a power outage, or other unexpected shutdown.

PCIE Port Configuration

AMI BIOS Setup Utility

55

Image 65

Intel N270 USB Function, USB 2.0 Controller, Audio Controller, SLPS4# Min. Assertion Width, Restore on AC Power Loss

Contents

Computer with Intel AtomTM N270 Processor Onboard User’s Manual All-in-One 8.4” SVGA TFT Fanless Touch PanelJuly 2009, Version A1 Printed in Taiwan DisclaimersCopyright 2009 Acnodes CorporationAll Rights Reserved FCC Compliance Safety ApprovalsSafety Precautions Trademarks Acknowledgments CHAPTER 2 HARDWARE INSTALLATION Table of ContentsCHAPTER 3 AMI BIOS SETUP UTILITY CHAPTER 1 INTRODUCTIONCHAPTER 4 DRIVERS INSTALLATION MEMO CHAPTER INTRODUCTION General Description Specification Dimensions I/O Outlets Package List1.1 General Description Reliable and Stable DesignBIOS 1.2 Specifications1.2.1 Main CPU Board Embedded O.S. Supported8.4” TFT LCD Heat Dispensing Design Net Weight 1.2.3 System SpecificationDimension Main Body Size Operation TemperatureNOTE All specifications and images are subject to change without notice This diagram shows you dimensions and outlines of the FPC 5084 1.3 DimensionsIntroduction Function 1.4 I/O OutletsDesktop Stand Kit optional VESA ARM optional Power Adapter optional 1.5 Packing ListFPC 5084 x 1 Panel Mount Kit x Driver CD Wall-Mount Kit Introduction2.1 CF card Installation CHAPTER HARDWARE INSTALLATIONWireless LAN Card CompactFlash Card Serial Port Ethernet Mounting Way DramStep 2 Find out the cover on the side of the system Hardware Installation2.2 Serial Ports Interface Hardware Installation Signal NamePin # RS-4222.3 Ethernet 2.4.1 Panel Mounting 2.4 Mountings - Panel/Wall/Desktop/VESAFind out the screws as marked on the back side of chassis 2.4.2 Wall-MountingStep 1 Find out the screws as marked on the back side of chassis 2.4.3 Desktop-MountingHardware Installation Step 2 Assemble the desktop stand to the chassis, and fix the screws Hardware InstallationFPC 5084 User Manual Step 1 Find out the screws as marked on the back side of chassis 2.4.4 VESA-ARM MountingHardware Installation FPC 5084 User Manual Step 3 VESA mounting Installation completedHardware Installation Hardware Installation 2. Find the SO-DIMM socket on mainboard SBC87830 2.5 DRAM Installation1. Unscrew six screws to remove the rear chassis 3. Push down latches on each side of the SO-DIMM socket Hardware Installation2.6 Wireless LAN Card Installation 3. Find the built-in Antenna cable which is tied with other cables on the top of the device. Connect antenna cable to MAIN connector on wireless LAN card FPC 5084 User Manual Hardware InstallationMEMO Page 3.2 Navigation Keys CHAPTER AMI BIOS SETUP UTILITY3.1 Starting System Time/Date 3.3 Main Menu3.4 Advanced Menu Execute-Disable Bit Capability Configure advanced CPU settingsMax CPUID Value Limit Hyper Threading TechnologyEnhanced C-States IDE ConfigurationSuperIO Configuration Serial Port1 IRQ Serial Port1 AddressSerial Port2 Address Serial Port2 IRQThis item specifies the IRQ used by the serial port Serial Port4 AddressSerial Port4 IRQ These items display the temperature of CPU and System, Vcore, etc Hardware Health ConfigurationSystem Temperature/CPU Temperature ACPI Settings Power Management/APM APM ConfigurationVideo Power Down Mode EnabledPower Button Mode Hard Disk Drive Power Down ModeSuspend Time Out Minute Throttle Slow Clock RatioAdvanced Resume Event Controls Resume On Ring Resume On RTC AlarmMPS Revision MPS ConfigurationActive State Power-Management PCI Express ConfigurationSB PCIE Ports Configuration BIOS EHCI Hand-Off USB ConfigurationLegacy USB Support USB 2.0 Controller Mode3.5 PCI PnP Menu Clear NVRAM PCI Latency TimerPlug & Play O/S Allocate IRQ to PCI VGAPCI IDE BusMaster Palette SnoopingOffBoard PCI/ISA IDE Card IRQ3/4/5/7/9/10/11/14/15Boot Settings Configuration Boot Device Priority Removable Drives 3.6 Boot MenuQuiet Boot Boot Settings Configuration Quick BootBoot Num-Lock AddOn ROM Display ModeHit ‘DEL’ Message Display Wait For ‘F1’ If ErrorBoot Device Priority Removable Drives Lan Boot Settings Configuration User Password Supervisor PasswordChange Supervisor Password Change User Passwordmenu. You can use the sub menu to change the user password Boot Sector Virus ProtectionDisabled EnabledNorth Bridge Configuration South Bridge Configuration 3.8 Chipset MenuConfigure DRAM Timing by SPD North Bridge Configuration DRAM FrequencyBoot Graphic Adapter Priority Video Function ConfigurationFPC 5084 User Manual AMI BIOS Setup UtilityAMI BIOS Setup Utility South Bridge ConfigurationPCIE Port Configuration Restore on AC Power LossUSB Function USB 2.0 ControllerSave Changes and Exit 3.9 Exit MenuDiscard Changes and Exit Discard ChangesLoad Fail-Safe Defaults Load Optimal DefaultsInstallation of Drivers CHAPTER DRIVERS INSTALLATION4.1 System 4.2 Touch Screen 4.2.1 Specification4.2.2 Driver Installation- Windows XP Installation of Drivers FPC 5084 User Manual Installation of Drivers4. Select the “Standard Calibrate” tab 5. Calibration 6. Press OKPenMount Touch screen 4.3 Embedded O.S4.3.1 Windows XP Embedded Calibration Touch screen 4.3.2 Windows CE.NET