Manuals / Intel / Computer Equipment / Tablet

Intel N270, FPC 5084 Wall-Mounting, Find out the screws as marked on the back side of chassis

Models: N270 FPC 5084

1 73

Download 73 pages 24.28 Kb

Page 23

2.4.2 Wall-Mounting

FPC 5084 User Manual

2.4.2 Wall-Mounting

The FPC 5084 is designed for Wall mounting application. Please refer to the following steps:

Find out the screws as marked on the back side of chassis.

Hardware Installation

15

Image 23

Intel N270, FPC 5084 user manual Wall-Mounting, Find out the screws as marked on the back side of chassis

Contents

Computer with Intel AtomTM N270 Processor Onboard User’s Manual All-in-One 8.4” SVGA TFT Fanless Touch PanelJuly 2009, Version A1 Printed in Taiwan DisclaimersCopyright 2009 Acnodes CorporationAll Rights Reserved FCC Compliance Safety ApprovalsSafety Precautions Trademarks Acknowledgments CHAPTER 1 INTRODUCTION Table of ContentsCHAPTER 2 HARDWARE INSTALLATION CHAPTER 3 AMI BIOS SETUP UTILITYCHAPTER 4 DRIVERS INSTALLATION MEMO Reliable and Stable Design General Description Specification Dimensions I/O Outlets Package ListCHAPTER INTRODUCTION 1.1 General DescriptionEmbedded O.S. Supported 1.2 SpecificationsBIOS 1.2.1 Main CPU BoardOperation Temperature 1.2.3 System Specification8.4” TFT LCD Heat Dispensing Design Net Weight Dimension Main Body SizeNOTE All specifications and images are subject to change without notice This diagram shows you dimensions and outlines of the FPC 5084 1.3 DimensionsIntroduction Function 1.4 I/O OutletsIntroduction 1.5 Packing ListDesktop Stand Kit optional VESA ARM optional Power Adapter optional FPC 5084 x 1 Panel Mount Kit x Driver CD Wall-Mount KitCompactFlash Card Serial Port Ethernet Mounting Way Dram CHAPTER HARDWARE INSTALLATION2.1 CF card Installation Wireless LAN CardStep 2 Find out the cover on the side of the system Hardware Installation2.2 Serial Ports Interface RS-422 Signal NameHardware Installation Pin #2.3 Ethernet 2.4.1 Panel Mounting 2.4 Mountings - Panel/Wall/Desktop/VESAFind out the screws as marked on the back side of chassis 2.4.2 Wall-MountingStep 1 Find out the screws as marked on the back side of chassis 2.4.3 Desktop-MountingHardware Installation Step 2 Assemble the desktop stand to the chassis, and fix the screws Hardware InstallationFPC 5084 User Manual Step 1 Find out the screws as marked on the back side of chassis 2.4.4 VESA-ARM MountingHardware Installation FPC 5084 User Manual Step 3 VESA mounting Installation completedHardware Installation Hardware Installation 2. Find the SO-DIMM socket on mainboard SBC87830 2.5 DRAM Installation1. Unscrew six screws to remove the rear chassis 3. Push down latches on each side of the SO-DIMM socket Hardware Installation2.6 Wireless LAN Card Installation 3. Find the built-in Antenna cable which is tied with other cables on the top of the device. Connect antenna cable to MAIN connector on wireless LAN card FPC 5084 User Manual Hardware InstallationMEMO Page 3.2 Navigation Keys CHAPTER AMI BIOS SETUP UTILITY3.1 Starting System Time/Date 3.3 Main Menu3.4 Advanced Menu Hyper Threading Technology Configure advanced CPU settingsExecute-Disable Bit Capability Max CPUID Value LimitEnhanced C-States IDE ConfigurationSuperIO Configuration Serial Port2 IRQ Serial Port1 AddressSerial Port1 IRQ Serial Port2 AddressThis item specifies the IRQ used by the serial port Serial Port4 AddressSerial Port4 IRQ These items display the temperature of CPU and System, Vcore, etc Hardware Health ConfigurationSystem Temperature/CPU Temperature ACPI Settings Enabled APM ConfigurationPower Management/APM Video Power Down ModeThrottle Slow Clock Ratio Hard Disk Drive Power Down ModePower Button Mode Suspend Time Out MinuteAdvanced Resume Event Controls Resume On Ring Resume On RTC AlarmMPS Revision MPS ConfigurationActive State Power-Management PCI Express ConfigurationSB PCIE Ports Configuration USB 2.0 Controller Mode USB ConfigurationBIOS EHCI Hand-Off Legacy USB Support3.5 PCI PnP Menu Allocate IRQ to PCI VGA PCI Latency TimerClear NVRAM Plug & Play O/SIRQ3/4/5/7/9/10/11/14/15 Palette SnoopingPCI IDE BusMaster OffBoard PCI/ISA IDE CardBoot Settings Configuration Boot Device Priority Removable Drives 3.6 Boot MenuAddOn ROM Display Mode Boot Settings Configuration Quick BootQuiet Boot Boot Num-LockHit ‘DEL’ Message Display Wait For ‘F1’ If ErrorBoot Device Priority Removable Drives Lan Boot Settings Configuration Change User Password Supervisor PasswordUser Password Change Supervisor PasswordEnabled Boot Sector Virus Protectionmenu. You can use the sub menu to change the user password DisabledNorth Bridge Configuration South Bridge Configuration 3.8 Chipset MenuVideo Function Configuration North Bridge Configuration DRAM FrequencyConfigure DRAM Timing by SPD Boot Graphic Adapter PriorityFPC 5084 User Manual AMI BIOS Setup UtilityAMI BIOS Setup Utility South Bridge ConfigurationUSB 2.0 Controller Restore on AC Power LossPCIE Port Configuration USB FunctionDiscard Changes 3.9 Exit MenuSave Changes and Exit Discard Changes and ExitLoad Fail-Safe Defaults Load Optimal DefaultsInstallation of Drivers CHAPTER DRIVERS INSTALLATION4.1 System 4.2 Touch Screen 4.2.1 Specification4.2.2 Driver Installation- Windows XP Installation of Drivers 6. Press OK Installation of DriversFPC 5084 User Manual 4. Select the “Standard Calibrate” tab 5. CalibrationPenMount Touch screen 4.3 Embedded O.S4.3.1 Windows XP Embedded Calibration Touch screen 4.3.2 Windows CE.NET