Invacare SX5, SX5 Recliner LABEL LOCATIONS

Tracer® SX5 6Part No. 1110550IMPORTANT NOTICE

The wheel locks on this wheelchair have been

pre-set at the factory to comply with the

Veterans Administration functional Standard

8320.01 of the Federal Register, paragraph

3.2.4.5.3. If these wheel locks do not meet

your needs, follow instructions below.

!

CAUTION

Any wheel lock adjustments should embed

wheel lock shoe at least 1/8" into tire when

locked (3/16" on pneumatic tires).

INSTRUCTIONS FOR WHEELLOCK ADJUSTMENTS

1. Loosen wheel lock mounting fastener,

which runs through mounting bracket and

frame.

2. Slide clamp toward rear wheel until wheel

lock shoe is embedded into tire material at

least 1/8" when handle is engaged to the

lock position (3/16" for pneumatic tires).

3. Tighten mounting fastener to secure

mounting bracket in desired location and

recheck lock shoe embedding.

4. Inspect for correct locking action BEFORE

actual use.

00078X021-0394

LABEL LOCATIONSLABEL LOCATIONSLABEL LOCATIONSWARNING

DETENT BALLS MUST BE SECURE-

LY SEATED IN RECESSED AREAS

OF AXLE BUSHINGS. ENSURE

THAT PLUNGER PIN IN HEAD END

OF AXLE IS FULLY RELEASED.

KEEP DETENT BALLS CLEAN.

1001948

MODELS WITHQUICK-RELEASEAXLES ONLYRefer to Owner's Manualfor proper anti-tippersetting.

1085379

WARNING

CrossmemberLower FrameTube14 TO 18-INCHWIDEWHEELCHAIRS(ONLY)20 TO 22-INCHWIDEWHEELCHAIRS(ONLY)

WARNING

DO NOT OPERATE WITHOUTTHE ANTI-TIP TUBESINSTALLED.

REV. 5/98 P/N 60106X144

RECLINER MODELS ONLYWARNING

DO NOT OPERATE WITHOUT

THE ANTI-TIP TUBES

INSTALLED.

REV. 5/98 P/N 60106X144

Contents

Main WARNING CONTENTS CONTENTS TABLE OF CONTENTS CONTENTS CONTENTS SPECIAL NOTES Tracer SX5 6Part No. 1110550 IMPORTANT NOTICE ! CAUTION LABEL LOCATIONS RECLINER MODELS ONLY LABEL LOCATIONS LABEL LOCATIONS WARNING SPECIFICATIONS SPECIFICATIONS SPECIFICATIONS INFORMATION FOR HEALTHCARE PROFESSIONALS/ ASSISTANTS STABILITY - ALL MODELS STABILITY - NON-RECLINER MODELS ONLY STABILITY - RECLINER MODELS ONLY OPERATING INFORMATION Page TIRE PRESSURE WEIGHT TRAINING WEIGHT LIMITATION SAFETY/HANDLING OF WHEELCHAIRS STABILITY AND BALANCE COPING WITH EVERYDAY OBSTACLES A NOTE TO WHEELCHAIR ASSISTANTS PERCENTAGE OF WEIGHT DISTRIBUTION TIPPING Page STAIRWAYS UNFOLDING AND FOLDING THE WHEELCHAIR TRANSFERRING TO AND FROM OTHER SEATS Page SECTION 2 SAFETY INSPECTION SAFETY INSPECTION CHECKLIST SAFETY INSPECTION TROUBLESHOOTING MAINTENANCE MAINTENANCE SAFETY PRECAUTIONSMAINTENANCE SAFETY PRECAUTIONS MAINTENANCE SAFETY PRECAUTIONSMAINTENANCE SAFETY PRECAUTIONS MAINTENANCE SAFETY PRECAUTIONS SUGGESTED MAINTENANCE PROCEDURES Page INSTALLING/REMOVING THE FOOTREST (FIGURE 1) HEEL LOOP REPLACEMENT (FIGURE 3) FOOTREST HEIGHT ADJUSTMENT (FIGURE 2) RAISING/LOWERING THE ELEVATING LEGREST ASSEMBLY (FIGURE 4) USING OR REPLACING FLIP-BACK ARMREST (FIGURE 1) USING REPLACING ADJUSTING ARMREST HEIGHT (FIGURE 2) INSTALLING THE BACK CANES (FIGURE 1) REPLACING BACK UPHOLSTERY (FIGURE 2) REPLACING SEAT UPHOLSTERY (FIGURE 3) ADJUSTING SEAT DEPTH (FIGURE 4) ADJUSTING THE SEAT WIDTH (FIGURE 5) SECTION 5 SEAT AND BACK SEAT AND BACK FIGURE 5 - ADJUSTING THE SEAT WIDTH DETAIL "A" DETAIL "B" - CROSSBRACE HARDWARE (STEPS 4,5) REMOVING/INSTALLING THE REAR WHEELS PERMANENT AXLES (FIGURE 1) QUICK-RELEASE AXLES (FIGURE 2) ADJUSTING THE QUICK-RELEASE AXLE (FIGURE 3) REPLACING REAR WHEEL HANDRIM (FIGURE 4) REPLACING/REPAIRING REAR WHEEL TIRE/TUBE INSTALLING/REPLACING FORK ASSEMBLIES (FIGURE 1) ADJUSTING FORKS (FIGURE 1) REPLACING FRONT CASTERS (FIGURE 2) REPLACING/REPAIRING FRONT CASTER TIRE/TUBE INSTALLING/ADJUSTING THE ANTI-TIPPERS INSTALLING THE ANTI-TIPPERS (FIGURES 1 AND 2) ADJUSTING THE ANTI-TIPPERS (FIGURE 3) WHEEL LOCK ADJUSTMENT(FIGURE 4) CHANGING SEAT-TO-FLOOR HEIGHT (FIGURES 1 AND 2) NON-RECLINER FRAME STYLE RECLINER FRAME STYLE RECLINER OPERATION (FIGURE 1) Page REPLACING THE HEADREST PILLOW (FIGURE 2) REPLACING THE HEADREST/BACK UPHOLSTERY (FIGURE 3) HEADREST UPHOLSTERY BACK UPHOLSTERY REMOVING/INSTALLING THE SPREADER BAR (FIGURE 4) REMOVING AND INSTALLING ARMREST (FIGURE 5) REMOVING ARMREST INSTALLING ARMREST REMOVING/INSTALLING THE REAR WHEELS (FIGURE 6) INSTALLING THE AMPUTEE BRACKET (FIGURE 1) INSTALLING THE SEAT POSITIONING STRAP (FIGURE 2) INSTALLING THE CRUTCH AND CANE CARRIER (FIGURE 3) INSTALLING THE TELESCOPING I.V. ROD (FIGURE 4) INSTALLING THE TELESCOPING I.V. ROD REPOSITIONING THE UPPER ATTACHMENT Page W A R R A N T Y OPTIONS MADE IN MEXICO LIMITED WARRANTY