Remote On/Off Switch, Mode Switch | Invacare TDX SI specification

SECTION 5—WHEELCHAIR OPERATION

Remote On/Off Switch

The remote On/Off switch input is located at the rear of the joystick on the right side and allows the power switch to be operated by an ability switch (normally open momentary switch with mono plug). To use the remote On/Off feature, the Drive Select/On/Off switch must be in the On position. Each activation of the ability switch will alternately turn the joystick On or Off.

Mode Switch

NOTE: For this procedure, refer to FIGURE 5.4 on page 38.

The mode switch is used to select the operating mode for the wheelchair. The mode switch is located on the joystick. A mode switch is needed whenever any of the following operating modes are programmed:

•Environmental Controls (ECU 1, ECU 2, ECU 3, ECU 4)*

•3 Speed Mode in Digital 3 Speed (Slow, Medium, Full)

•Latched Modes

•Sleep Mode

•RIM Mode*

•Remote Drive Selection Mode*

•Tilt/Recline Mode*

•Information Center Display Selection (does not require Reset activation at power up)

If any of the above modes are selected, the control will require activation of the switch immediately after the power switch is turned On in order to enter the drive mode. The second line of the LCD will display ‐ PRESS RESET.

*NOTE: In these modes, Standby Select allows the reset switch to be bypassed for users unable to activate the switch.

Memory Card Slot

The memory card slot is used with the basic or professional memory card for saving or reading wheelchair parameters.

TDX® SI, TDX SI-HD

42

Part No 1154294

Image 42

Invacare TDX SI manual Remote On/Off Switch, Mode Switch, Memory Card Slot

Contents

TDX SI TDX SI-HD Reference Documents Reference DocumentsManual Table of Contents Safety INSPECTION/TROUBLESHOOTING Wheel Locks Register Your Product Transport Ready Package Trro Special Notes Special NotesMeaning Trro and Trbkts Warnings Wheelchairs with 22NF Batteries Label LocationsAll Wheelchairs Label Locations Wheelchairs with Trro Wheelchairs without Trro Typical Product Parameters Typical Product ParametersTDX SI HD Operation Information Repair or Service InformationGeneral Guidelines General Guidelines General Guidelines Electrical Wheelchairs with Trro or Trbkts OnlyGrounding Instructions Batteries Charging Batteries Weight Training Weight LimitationRain Test EMI Information EMI Information EMI Information SAFETY/HANDLING of Wheelchairs SAFETY/HANDLING of WheelchairsStability and Balance SAFETY/HANDLING of Wheelchairs Stability Assist Coping with Everyday Obstacles Reaching, Leaning and Bending Forward Reaching, Leaning and Bending Reaching, Bending Backward Pinch Points Stairways Transferring To and From Other Seats Transferring To and From Other Seats Inspect/Adjust Initially Safety INSPECTION/ TroubleshootingSafety Inspection Checklists Safety INSPECTION/TROUBLESHOOTING Inspect/Adjust Weekly Inspect/Adjust Monthly Inspect/Adjust Every 18 Months Troubleshooting MechanicalInspect/Adjust Periodically Inspect/Adjust Every 2 Years SPJ+, SPJ+ w/PSS or SPJ+ w/ACC Joysticks Troubleshooting ElectricalInformation Gauge Display Diagnostics Display Description Definition Symptom Probable Cause Solutions Service Indicator Light DiagnosticsPossible Solution MPJ+, PSR+, PSF+ Joysticks or Displays BAD Joystick CAL Values Checking Battery Charge Level DON’T Wheelchair Operation Turning the Power On/OffUsing the Joystick to Drive the Wheelchair Operating the Wheelchair Movement Action Wheelchair On/Off Button Speedometer Joystick Service IndicatorSpeed Control Buttons Charger/Programming Input Selecting the Drive Mode MPJ+ Joystick Switches and IndicatorsDrive Select Toggle Switch Information Gauge Display Speed Control LCD Display Screens Splash Screen Main Screen Wheelchair Operation Description Driving Screen Remote Mode Reset Switch Programmable Mono Port 1/2 or External Mode SwitchRemote Stop Switch Connected Devices Screen Remote On/Off Switch Mode SwitchMemory Card Slot Repositioning Joystick Van Seats Disconnecting Disconnecting/Connecting the JoysticksAdjustable Asba Seats SPJ+ Joysticks Connecting MPJ+ Joysticks Motor Locks Disengaging/Engaging Motor Lock LeversMotor Locks Engaging Wheel LocksDisengaging/Engaging the Wheel locks Disengaging Installing Footboard AssemblyRemoving/Installing the Footboard Pinch point may occur when rotating the footboard assembly Adjusting the Footboard Angle Removing/Installing the Footboard Adjusting Forks ForksForks Batteries Batteries Using the Proper Batteries For Wheelchairs Using 22NF Batteries Wire Cutter Replacing Batteries Replacing Batteries Cleaning Battery Terminals Removing/Installing the Batteries From/Into the Wheelchair Battery Retention Bracket Installing Batteries into Wheelchair Removing the Batteries from Wheelchair Installing Batteries into Wheelchair When to Charge Batteries SPJ+, SPJ+ w/PSS and SPJ+ w/ACC JoysticksMPJ+ Joystick Description and Use of Battery Chargers Charging Batteries Required Items Tool Quantity Transport Ready Package Trro Transport Ready Package Trro About Transport Ready Packages Compliance Information Securing the Wheelchair to the Vehicle SpecificationsMotor Wheelchair Weight Limit Positioning the Wheelchair in the Vehicle Securing the Wheelchair Securement Points Securing the Occupant Wheelchair-Anchored Belts Wheelchair-Anchored Belts Vehicle-Anchored Belts Rating Description Seating System Positioning Belts TDX SI, TDX SI-HD Limited Warranty Global Limited Warranty Excluding Canada Limited Warranty Canada Limited Warranty USA