Jenn-Air 8113P714-60 Care & Cleaning, Before Self-Cleaning, To set Self-Clean, Self-Clean Oven

CARE & CLEANING

Self-Clean Oven

CAUTION

•It is normal for parts of the oven to become hot during a self-clean cycle.

•To prevent damage to oven door, do not attempt to open the door when LOCK is displayed.

•Avoid touching door, window or oven vent area during a clean cycle.

•Do not use commercial oven cleaners on the oven finish or around any part of the oven. They will damage the finish or parts.

The self-clean cycle uses above-normal cooking temperatures to automatically clean the oven interior.

The oven should be cleaned regularly by wiping up spillovers to prevent excessive smoke and flare-ups. Do not allow a heavy build-up of soil to accumulate in the oven.

During the cleaning process, the kitchen should be well ventilated to get rid of normal odors associated with cleaning.

Before Self-Cleaning

1.Turn off the oven light before cleaning. The oven light may burn out during the clean cycle.

2.Remove broiler pan, all pans, and oven racks from the oven. The oven racks will discolor and may not slide easily

after a self-clean cycle if they are not removed.

3. Clean oven frame, door frame, area outside of gasket, and around the opening in the door gasket with a nonabrasive cleaner such as Bon

Ami* or detergent and water. The

self-cleaning process does not clean these areas. They should be cleaned to prevent soil from baking on during the clean cycle. (The gasket is the seal around the oven door and window.)

4.To prevent damage, do not clean or rub the gasket around the oven door. The gasket is designed to seal in heat during the clean cycle.

5.Wipe up excess grease or spill-overs from the oven bottom. This prevents excessive smoking, flare-ups or flaming during the clean cycle.

6.Wipe up sugary and acidic spillovers such as sweet potatoes, tomato, or milk-based sauces. Porcelain enamel is acid-resistant, not acid-proof. The porcelain finish may discolor if acidic or sugary spills are not wiped up before a self-clean cycle.

To set Self-Clean:

1.Press Clean pad.

2.REMOVE RACKS will be displayed. Remove the racks.

3.Select CONTINUE using the Quickset pad. The Quickset pads are located on either side of the control panel display.

4.Set LIGHT soil level by entering 200 using the number pads for two hours of cleaning time. Press the Enter pad.

OR

Select MEDIUM for a moderately soiled oven and three hours of cleaning time.

OR

Select HEAVY for a heavily soiled oven and four hours of cleaning time.

5.CLEAN, TIME, LOCKED and the cleaning time countdown will be displayed while the oven is cleaning. OVEN COOLING will appear in the display when the cleaning time has been completed and the oven is still locked.

Important: The door lock will disengage approximately one hour after the cleaning time is completed. OVEN COOLING will go off in the display when the oven door has unlocked.

To Delay a Self-Clean Cycle:

1. Press Clean pad.

2. REMOVE RACKS will be displayed. Remove the racks.

3.Select CONTINUE using the Quickset pad.

4.Set LIGHT soil level by entering 200 using the number pads for two hours of cleaning time. Press the Enter pad.

OR

Select MEDIUM for a moderately soiled oven and three hours of cleaning time.

OR

Select HEAVY for a heavily soiled oven and four hours of cleaning time.

5.The door will lock. CLEAN, TIME, LOCKED and the cleaning time countdown will be displayed

6.After door locks, press the More Options pad.

7.Select DELAY using the Quickset pad.

8.Select the number of hours you want to delay the start of the self-clean cycle.

9.The delay time and cleaning time will be displayed.

* Brand names for cleaning products are registered trademarks of the respective manufacturers.

5