INSTALLATION INSTRUCTIONS

Prepare Location

■It is recommended that the vent system be installed before hood is installed.

■Before making cutouts, make sure there is proper clearance within the ceiling or wall for exhaust vent.

■Check your ceiling height and the hood height maximum before you select your hood.

1.Disconnect power.

2.Determine which venting method to use: roof, wall, or non- vented.

3.Select a flat surface for assembling the range hood. Place covering over that surface.

WARNING

Excessive Weight Hazard

Use two or more people to move and install range hood.

Failure to do so can result in back or other injury.

4.Using 2 or more people, lift range hood onto covered surface.

8.Mark centers of the fastener locations through the template to the wall. For rear venting through the wall, mark the opening for the 3¼" x 10" (8.3 x 25.4 cm) rectangular vent.

IMPORTANT: All screws must be installed into wood. If there is no wood to screw into, additional wall framing supports may be required.

Remove the template.

9.Drill ³⁄₁₆" (4.8 mm) pilot holes at all locations where screws are being installed into wood.

10.Install the 2 - 5 x 45 mm mounting screws. Leave a

¹⁄₄" (6.4 mm) gap between the wall and the back of the screw head to slide range hood into place.

¹⁄₄" (6.4 mm)

Vent Cover Bracket Installation (for vent cover installation only)

1.Attach vent cover bracket to wall flush to the ceiling using 2 - 5 x 45 mm screws.

Range Hood Mounting Screws Installation

5.Determine and mark the centerline on the wall where the canopy hood will be installed.

6.Select a mounting height between a minimum of

18" (45.7 cm) for an electric cooking surface or a minimum of 22" (55.9 cm) for a gas cooking surface, and a suggested maximum of 24" (61.0 cm) above the range to the bottom of the hood. Mark a reference line on the wall.

7.Tape template in place, aligning the template centerline and bottom of template with hood bottom line and with the centerline marked on the wall.

A

B

A.Centerline

B.Mounting height reference

A

B

C

A.Ceiling

B.Wall

C.Centerline

Complete Preparation

1.Determine and make all necessary cuts in the wall for the vent system. Install the vent system before installing the hood. See “Venting Requirements” section.

2.Determine the required height for the home power supply cable and drill a 1¼" (3.2 cm) hole at this location.

3.Run the home power supply cable according to the National Electrical Code or CSA Standards and local codes and ordinances. There must be enough ½" conduit and wires from the fused disconnect (or circuit breaker) box to make the connection in the hood’s electrical terminal box.

NOTE: Do not reconnect power until installation is complete.

4.Use caulk to seal all openings.

7

Page 6 Page 8
Page 7
Image 7
Jenn-Air LI3URB/W10274314C Installation Instructions, Prepare Location, Range Hood Mounting Screws Installation
Page 6 Page 8

LI3URB/W10274314C, W10274314C specifications

The Jenn-Air W10274314C, also known as the LI3URB, is a sophisticated appliance that embodies modern cooking technology and user-friendly features. As part of Jenn-Air's esteemed line of kitchen products, this model is designed to enhance culinary experiences, making it a staple for both amateur cooks and experienced chefs.

One of the standout features of the Jenn-Air W10274314C is its impressive performance capability. This appliance is engineered to deliver precise temperature control, allowing for a more consistent cooking experience. It utilizes advanced technology to ensure that your dishes are cooked evenly, providing delicious results every time. The design includes multiple burner configurations, enabling users to prepare various dishes simultaneously while maintaining optimal heat levels.

Additionally, the LI3URB/W10274314C showcases a sleek, modern aesthetic that seamlessly blends into any kitchen décor. Its stainless steel finish not only adds a touch of elegance but also ensures durability and ease of cleaning. The appliance is equipped with a spacious cooking surface, making it ideal for family meals and entertaining guests.

Another notable characteristic is its exceptional safety features. The Jenn-Air W10274314C includes an automatic shut-off function, ensuring peace of mind when using the appliance. This innovative technology helps prevent overheating and reduces the risk of accidents in the kitchen.

Furthermore, the appliance boasts an intuitive control panel, making it easy to navigate through various settings. Users can select from a range of cooking modes and adjust the temperature with precision. The built-in timer is a useful addition, allowing you to focus on other tasks without the fear of overcooking.

The Jenn-Air LI3URB/W10274314C is also compatible with various cooking styles, from gas to induction heating, catering to diverse culinary preferences. Whether simmering sauces, searing meats, or steaming vegetables, this appliance handles it all with finesse.

In summary, the Jenn-Air W10274314C, LI3URB/W10274314C presents a blend of design, safety, and advanced cooking technology. Its features make it an excellent choice for anyone looking to elevate their cooking experience while enjoying the benefits of modern kitchen innovations.
Top Page Image Contents